Dji fcc esp32
nikolaus018·dji-fcc-esp32·hardware/dji-fcc.kicad_pcb
About the Dji fcc esp32 PCB
Dji fcc esp32 is an open source ESP32 PCB design by nikolaus018, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 34 mm, with 56 components from 36 distinct parts.
Its main chip is the ESP32-S3-MINI-1-N8, from the ESP32 family. Other key parts include the AP2112K-3.3TRG1, TP4056-42-ESOP8, DW01A, MT3608 and TPS2553DBVR. By type, the board carries 21 resistors, 15 capacitors, 9 ICs, 6 diodes, 3 connectors and 1 transistor.
It belongs with the power & battery and rf & radio designs in this gallery.
From the project
ESP32-S3 firmware that switches a DJI N1 remote to FCC mode over USB (replaces the Android app)
A small battery-powered dongle that replaces the Android phone in the DJI N1 "FCC patch" workflow: plug it into the remote's bottom USB-C port, it powers the port, sends the patch, shows the result on an LED and goes back to sleep. Charge it over USB-C.
Status: rev A, ready to order a prototype batch. Not yet built or tested on real hardware. Everything below was checked by KiCad ERC/DRC and by cross-checking datasheets; nothing has been powered up. See Before you call it production.

Main components on the Dji fcc esp32
Dji fcc esp32 bill of materials (BOM)
56 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-MINI-1-N8 | ESP32-S2-MINI-1 | U1 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | TP4056-42-ESOP8 TP4056 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm | U3 |
| 1 | DW01A | SOT-23-6 | U4 |
| 1 | MT3608 | SOT-23-6 | U5 |
| 1 | TPS2553DBVR | SOT-23-6 | U6 |
| 2 | USBLC6-2SC6 | SOT-23-6 | U7, U9 |
| 1 | FSUSB42MUX | MSOP-10_3x3mm_P0.5mm | U8 |
| 1 | FS8205A | TSSOP-8_4.4x3mm_P0.65mm | Q1 |
| 1 | TYPE-C-31-M-12 USB-C REMOTE | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | TYPE-C-31-M-12 USB-C CHARGE | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | S2B-PH-SM4-TB BATTERY 1S LiPo (+ on pin 1) | JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J3 |
| 2 | SMF5.0A | D_SOD-123F | D1, D5 |
| 1 | SS34 | D_SMA | D4 |
| 1 | C2286 RED | LED_0603_1608Metric | D6 |
| 1 | C2986059 GREEN | LED_0603_1608Metric | D7 |
| 1 | C2986058 BLUE | LED_0603_1608Metric | D8 |
| 1 | SWPA4020S4R7MT 4.7uH | L_Sunlord_SWPA4020S | L1 |
| 1 | 1UF 1uF | C_0603_1608Metric | C1 |
| 6 | 10UF 10uF | C_0805_2012Metric | C2, C4, C5, C6, C7, C13 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | 100NF 100nF | C_0603_1608Metric | C3, C8, C12, C14, C15 |
| 3 | 22UF 22uF | C_0805_2012Metric | C9, C10, C11 |
| 1 | 10K 10k | R_0603_1608Metric | R1 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R2, R3 |
| 1 | 4.7K 4.7k | R_0603_1608Metric | R4 |
| 1 | 100 | R_0603_1608Metric | R7 |
| 1 | 1k | R_0603_1608Metric | R8 |
| 1 | 220K 220k | R_0603_1608Metric | R9 |
| 1 | 30K 30k | R_0603_1608Metric | R10 |
| 4 | 100K 100k | R_0603_1608Metric | R11, R13, R14, R22 |
| 1 | 47K 47k | R_0603_1608Metric | R12 |
| 2 | 33K 33k | R_0603_1608Metric | R15, R16 |
| 2 | 470 | R_0603_1608Metric | R17, R18 |
| 1 | 220 | R_0603_1608Metric | R19 |
| 2 | 1M | R_0603_1608Metric | R20, R21 |
| 1 | 150K 150k | R_0603_1608Metric | R23 |
Dji fcc esp32 design files
The KiCad project lives in the nikolaus018/dji-fcc-esp32 repository on GitHub; these links point at the commit this page was built from.
Dji fcc esp32: common questions
What microcontroller does the Dji fcc esp32 use?
The Dji fcc esp32 is built around the ESP32-S3-MINI-1-N8, from the ESP32 family.
How big is the Dji fcc esp32 PCB?
The Dji fcc esp32 measures 80 × 34 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Dji fcc esp32?
56 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Dji fcc esp32 design files?
From the nikolaus018/dji-fcc-esp32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Dji fcc esp32 design in my own project?
Yes, under the terms of its MIT license, which nikolaus018 chose for the repository.
Can I test firmware for the Dji fcc esp32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k