Ledify

notaroomba·ledify·pcb/ledify.kicad_pcb

Ledify PCB layout, top view — open source ESP32 board by notaroomba

About the Ledify PCB

Ledify is an open source ESP32 PCB design by notaroomba, published on GitHub. It is a 4-layer board measuring 35.5 × 52.5 mm, with 79 components from 40 distinct parts.

Its main chip is the ESP32-C6, from the ESP32 family. Other key parts include the USBLC6-2P6, AP63203WU, FUSB302BMPX, W25Q128JVP and LM61495QRPHRQ1. By type, the board carries 44 capacitors, 11 resistors, 10 ICs, 4 connectors, 4 inductors and 2 crystals.

It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.

From the project

- ESP32-C6 microcontroller with Wi-Fi 6 and Bluetooth LE - 16MB flash (W25Q128JVP) - USB-C PD up to 100W with the FUSB302B - Switchable 5V/12V LED output from a 10A buck converter (LM61495), selected in software - Addressable LED pads (VCC / SIG / GND) for WS2812B, WS2811 and WS2

- ESP32-C6 microcontroller with Wi-Fi 6 and Bluetooth LE - 16MB flash (W25Q128JVP) - USB-C PD up to 100W with the FUSB302B - Switchable 5V/12V LED output from a 10A buck converter (LM61495), selected in software - Addressable LED pads (VCC / SIG / GND) for WS2812B, WS2811 and WS2815 strips - IMU and Barometer - BMI323 (6-axis) and BMP581 pressure sensor - Ambient light sensor (OPT4001) for automatic brightness - I2S microphone (ICS-43434) for sound-reactive effects - PCB trace antenna with an impedance matching network - 3.3V buck converter (AP63203) for the logic side - ESD protection on the…

Ledify, from the project README
From the project README

Main components on the Ledify

Ledify bill of materials (BOM)

79 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-C6
ESP32-C6_C5364646
ESPRESSIF(乐鑫)
U1
1
USBLC6-2P6
U2
1
AP63203WU
U3
1
FUSB302BMPX
U4
1
W25Q128JVP
U5
1
LM61495QRPHRQ1
TI(德州仪器)
U6
1
BMI323
Bosch(博世)
U7
1
BMP581
Bosch(博世)
U8
1
OPT4001DNPRQ1
TI(德州仪器)
U10
1
ICS-43434
ICS-43434_C5656610
TDK InvenSense(应美盛)
U11
1
2N7002K
Q1
1
XL2EL89COI-111YLC-40M
YXC(扬兴晶振)
X1
1
Q13FC13500004
Q13FC1350000400
EPSON(爱普生)
X2
3
CONN_01X01_PIN
Conn_01x01_Pin
J1, J3, J4
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J2
1
Antenna_Shield
AE1
2
TS-1088-AR02016
XUNPU(讯普)
SW1, SW2
1
ZEMS1770-6R8M
ZE(增益)
L1
1
XRCD43-3R9M
XR(祥如)
L2
1
VHF160808H2N0ST
FH(风华)
L3
Show 20 more
QtyPartRefs
1
TCGL1005B1N8SAT
CCTC(三环)
L5
1
4.7UF35V
4.7uFn35V
C1
2
470PF
470pF
C2, C3
1
100NF
100nF
C4
3
10UF50V
10uFn50V
C5, C7, C15
2
470NF50V
470nFn50V
C6, C8
1
1UF
1uF
C9
5
22UF25V
22uFn25V
C10, C11, C12, C13, C14
14
100NF
100nF
C16, C19, C20, C24, C26, C27, C30, C31 +6
2
22UF
22uF
C17, C18
5
1UF
1uF
C21, C25, C28, C33, C36
4
18PF
18pF
C22, C23, C34, C35
1
10UF
10uF
C29
1
10NF
10nF
C32
1
4PF
4pF
C41
1
4.6PF
4.6pF
C42
2
100K
R1, R2
1
24.9K
R3
1
14.3K
R4
7
4.7K
R5, R6, R7, R8, R9, R10, R11

Ledify design files

The KiCad project lives in the notaroomba/ledify repository on GitHub; these links point at the commit this page was built from.

Ledify: common questions

What microcontroller does the Ledify use?

The Ledify is built around the ESP32-C6, from the ESP32 family.

How big is the Ledify PCB?

The Ledify measures 35.5 × 52.5 mm, has 4 copper layers and is 1.5842 mm thick.

How many components are on the Ledify?

79 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Ledify design files?

From the notaroomba/ledify repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Ledify design in my own project?

The repository has no license, so all rights stay with notaroomba. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Ledify without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards