Default
Shmcandi·esp32-devkit-hardware·esp32c6/layouts/default/default.kicad_pcb
About the Default PCB
Default is an open source ESP32 PCB design by Shmcandi, published on GitHub. It is a 2-layer board measuring 30 × 76 mm, with 33 components from 20 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the AMS1117-3.3 and CH340C. By type, the board carries 10 resistors, 9 capacitors, 4 connectors, 3 ICs, 3 diodes and 2 transistors.
It belongs with the dev boards & breakouts, displays & leds and usb & debug tools designs in this gallery.
From the project
Production-grade ESP32-WROOM-32E and ESP32-S3 (N16R8) Dual USB-C development board PCB designs created with Atopile & KiCad 10
This repository contains production-ready, breadboard-compatible hardware designs for Espressif microcontroller development boards, architected using Atopile (code-defined electronics) and automated layout/routing with KiCad 10 and Freerouting:
1. pcb2: ESP32-WROOM-32E DevKit (CP2102/CH340 USB-to-UART bridge, auto-programming circuit, dual 19-pin DIP headers). 2. esp32c6: ESP32-S3 (N16R8) DevKit (Dual USB-C ports: Native USB OTG + Hardware UART via CH340C, Addressable SK6812MINI / WS2812B RGB LED on GPIO48, 16MB Flash, 8MB Octal PSRAM, dual 22-pin DIP headers, dedicated antenna keepout).

Main components on the Default
Default bill of materials (BOM)
33 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1 | U2 |
| 1 | CH340C | SOP-16_4.4x10.4mm_P1.27mm | U3 |
| 2 | S8050 | SOT-23 | Q1, Q2 |
| 1 | HDR-L | PinHeader_1x22_P2.54mm_Vertical | J1 |
| 1 | HDR-R | PinHeader_1x22_P2.54mm_Vertical | J2 |
| 1 | USB | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | UART | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | BOOT | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | RESET | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | BLUE | LED_0603_1608Metric | D2 |
| 1 | SK6812MINI | LED_SK6812MINI_PLCC4_3.5x3.5mm_P1.75mm | D3 |
| 1 | 1uF | C_0603_1608Metric | C1 |
| 2 | 10uF | C_0603_1608Metric | C2, C4 |
| 5 | 100nF | C_0603_1608Metric | C3, C5, C7, C8, C9 |
| 1 | 22uF | C_0603_1608Metric | C6 |
| 4 | 10k | R_0603_1608Metric | R1, R6, R7, R9 |
| 4 | 5.1k | R_0603_1608Metric | R2, R3, R4, R5 |
| 2 | 1k | R_0603_1608Metric | R8, R10 |
Default design files
The KiCad project lives in the Shmcandi/esp32-devkit-hardware repository on GitHub; these links point at the commit this page was built from.
Default: common questions
What microcontroller does the Default use?
The Default is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the Default PCB?
The Default measures 30 × 76 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Default?
33 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Default design files?
From the Shmcandi/esp32-devkit-hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Default design in my own project?
The repository has no license, so all rights stay with Shmcandi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Default without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in esp32-devkit-hardware
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k