Prosthetic

SoumyadeepXD·prosthetic·hardware/schematics/vapa_main.kicad_sch

This repository ships a schematic but no board layout.

About the Prosthetic PCB

Prosthetic is an open source ESP32 PCB design by SoumyadeepXD, published on GitHub. It is a board, with 67 components from 48 distinct parts.

Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the PCA9685PW, TCA9548APWR, ADS1115IDGSR, ISO1540DR and B0505S-1WR3. By type, the board carries 21 connectors, 12 capacitors, 10 ICs, 8 resistors, 4 fuses and 1 switch.

It belongs with the robotics & motion designs in this gallery.

From the project

VAPA is an advanced multi-modal active transradial robotic prosthetic arm combining dual-processor shared control, biological muscular intent (two-site surface electromyography), closed-loop force and magnetic encoder feedback, and real-time computer vision (RGB-D object classifi

VAPA is an advanced multi-modal active transradial robotic prosthetic arm combining dual-processor shared control, biological muscular intent (two-site surface electromyography), closed-loop force and magnetic encoder feedback, and real-time computer vision (RGB-D object classification and distance tracking).

Deliverables located in hardware/: - Schematics (hardware/schematics/): - vapamain.kicadsch (Master hierarchical schematic) - powerdistribution.kicadsch (XT60, 30A fuse, PROFET BTS50015, dual 6V/15A bucks, AP2112K LDO) - esp32controller.kicadsch (ESP32-WROOM-32E, GPIO25 OE pullup, PC817…

Main components on the Prosthetic

Prosthetic bill of materials (BOM)

67 components, 48 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-WROOM-32E-N4
Espressif Systems
U2
1
PCA9685PW
NXP Semiconductors
U3
1
TCA9548APWR
Texas Instruments
U4
1
ADS1115IDGSR
Texas Instruments
U5
1
ISO1540DR
Texas Instruments
U6
1
B0505S-1WR3
Mornsun
U7
1
AP2112K-3.3TRG1
AP2112K-3.3
Diodes Incorporated
U8
1
TPS79333DBVR
Texas Instruments
U9
1
BTS50015-1TMA
Infineon Technologies
U10
1
PC817_OPTO
U11
1
0022232031
SERVO_THUMB_MG996R
Molex
J1
1
0022232031
SERVO_INDEX_MG996R
Molex
J2
1
0022232031
SERVO_MIDDLE_MG996R
Molex
J3
1
0022232031
SERVO_RING_MG996R
Molex
J4
1
0022232031
SERVO_LITTLE_MG996R
Molex
J5
1
0022232031
SERVO_WRIST_PITCH_DS3225
Molex
J6
1
0022232031
SERVO_WRIST_ROLL_DS3225
Molex
J7
1
0022232031
SERVO_WRIST_DEV_DS3225
Molex
J8
1
0022232031
SERVO_FOREARM_ROT_DS3218
Molex
J9
1
ENC_FINGER_GROUP_AS5600
J10
Show 28 more
QtyPartRefs
1
ENC_WRIST_FLEX_AS5600
J11
1
ENC_WRIST_ROTATE_AS5600
J12
1
ENC_FOREARM_ROT_AS5600
J13
1
MYOWARE_CH1_FLEXOR
J14
1
MYOWARE_CH2_EXTENSOR
J15
1
0532610271
FSR_THUMB_CONN
Molex
J16
1
0532610271
FSR_INDEX_CONN
Molex
J17
1
0532610271
FSR_MID_CONN
Molex
J18
1
0532610271
FSR_RING_CONN
Molex
J19
1
0532610271
FSR_LITTLE_CONN
Molex
J20
1
AUX_CRANIAL_EEG
J21
1
XT60H-M
XT60_BATTERY_12V
Amass
CONN1
1
0257030.PXPV
30A_ATO_BLADE
Littelfuse
F1
2
0257015.PXPV
15A_ATO_BLADE
Littelfuse
F2, F3
1
16R600G
6A_PTC_RESETTABLE
Littelfuse
F4
1
4x4.7k_SDA_PULLUPS
RP1
1
4x4.7k_SCL_PULLUPS
RP2
1
AB6E-3BV01PRM
IDEC_ESTOP_NC
IDEC
SW1
5
SP3002-04UTG
SP3002_3.3V
Littelfuse
TVS1, TVS2, TVS3, TVS4, TVS5
1
TPS54620RGYR
TPS54620_5V_6A
Texas Instruments
VR1
2
D36V50F6_6V_15A
VR2, VR3
4
UHW1C222MPD
2200uF_16V_LOW_ESR
Nichicon
C1, C2, C3, C4
1
10uF_X7R
C5
7
0.1uF_X7R
C6, C7, C8, C9, C10, C11, C12
5
MBA02040C1002BCT00
10.0k_0.1%
Vishay Beyschlag
R1, R2, R3, R4, R5
1
10k_0.1%
R6
1
4.7k_SDA
R7
1
4.7k_SCL
R8

Prosthetic design files

The KiCad project lives in the SoumyadeepXD/prosthetic repository on GitHub; these links point at the commit this page was built from.

Prosthetic: common questions

What microcontroller does the Prosthetic use?

The Prosthetic is built around the ESP32-WROOM-32E-N4, from the ESP32 family.

How many components are on the Prosthetic?

67 components, from 48 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Prosthetic design files?

From the SoumyadeepXD/prosthetic repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.

Can I use the Prosthetic design in my own project?

The repository has no license, so all rights stay with SoumyadeepXD. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Prosthetic without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards