Esp gari
Vulcan758·My-PCB-Designs-·esp_gari/esp_gari.kicad_pcb
About the Esp gari PCB
Esp gari is an open source ESP32 PCB design by Vulcan758, published on GitHub. It is a 4-layer board measuring 50.5 × 63.9 mm, with 38 components from 22 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the AMS1117-3.3 and TB6612FNG. By type, the board carries 19 capacitors, 5 connectors, 5 resistors, 3 ICs, 2 switches and 2 inductors.
From the project
all the designs I have so far
Main components on the Esp gari
Esp gari bill of materials (BOM)
38 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U3 |
| 1 | 40MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Conn_Coaxial | SMA_Molex_73251-1153_EdgeMount_Horizontal | J2 |
| 1 | Motor_1 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J4 |
| 1 | Motor_2 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J5 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J6 |
| 2 | SW_Push | SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 2 | 2.2n | L_0402_1005Metric | L1, L2 |
| 3 | 10u | C_0603_1608Metric | C1, C11, C13 |
| 1 | 0.1u | C_0603_1608Metric | C2 |
| 5 | 100n | C_0402_1005Metric | C3, C6, C7, C8, C10 |
| 2 | 10p | C_0603_1608Metric | C4, C5 |
| 2 | 3.3p | C_0402_1005Metric | C9, C12 |
| 2 | 22u | C_1210_3225Metric | C14, C15 |
| 2 | 0.1uF | C_0603_1608Metric | C16, C18 |
| 2 | 10uF | C_0603_1608Metric | C17, C19 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 5.7k | R_0805_2012Metric | R1, R2, R4, R5 |
| 1 | 22k | R_0402_1005Metric | R3 |
Esp gari design files
The KiCad project lives in the Vulcan758/My-PCB-Designs- repository on GitHub; these links point at the commit this page was built from.
- Layoutesp_gari/esp_gari.kicad_pcb
- Schematicesp_gari/esp_gari.kicad_sch
Esp gari: common questions
What microcontroller does the Esp gari use?
The Esp gari is built around the ESP32-S3, from the ESP32 family.
How big is the Esp gari PCB?
The Esp gari measures 50.5 × 63.9 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Esp gari?
38 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp gari design files?
From the Vulcan758/My-PCB-Designs- repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp gari design in my own project?
The repository has no license, so all rights stay with Vulcan758. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp gari without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in My-PCB-Designs-
AVR/Arduino
IR array sensor
Vulcan758
131.5 × 133.3 mm57 parts2LNo license0AVR/Arduino
IR array sensor - Copy
Vulcan758
113.5 × 138 mm57 parts2LNo license0ESP32
Saucey - Copy
Vulcan758
80.5 × 40.8 mm52 parts2LNo license0ESP32
Saucey
Vulcan758
74.5 × 41.3 mm48 parts2LNo license0ESP32
Esp gari - Copy
Vulcan758
50.5 × 68.3 mm38 parts4LNo license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k