Esp gari - Copy
Vulcan758·My-PCB-Designs-·esp_gari/v1/esp_gari - Copy.kicad_pcb
About the Esp gari - Copy PCB
Esp gari - Copy is an open source ESP32 PCB design by Vulcan758, published on GitHub. It is a 4-layer board measuring 50.5 × 68.3 mm, with 38 components from 22 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the AMS1117-3.3 and TB6612FNG. By type, the board carries 19 capacitors, 5 connectors, 5 resistors, 3 ICs, 2 switches and 2 inductors.
From the project
all the designs I have so far
Main components on the Esp gari - Copy
Esp gari - Copy bill of materials (BOM)
38 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U3 |
| 1 | 40MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Conn_Coaxial | SMA_Molex_73251-1153_EdgeMount_Horizontal | J2 |
| 1 | Motor_1 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J4 |
| 1 | Motor_2 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J5 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J6 |
| 2 | SW_Push | SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 2 | 2.2n | L_0402_1005Metric | L1, L2 |
| 3 | 10u | C_0603_1608Metric | C1, C11, C13 |
| 1 | 0.1u | C_0603_1608Metric | C2 |
| 5 | 100n | C_0402_1005Metric | C3, C6, C7, C8, C10 |
| 2 | 10p | C_0603_1608Metric | C4, C5 |
| 2 | 3.3p | C_0402_1005Metric | C9, C12 |
| 2 | 22u | C_1210_3225Metric | C14, C15 |
| 2 | 0.1uF | C_0603_1608Metric | C16, C18 |
| 2 | 10uF | C_0603_1608Metric | C17, C19 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 5.7k | R_0805_2012Metric | R1, R2, R4, R5 |
| 1 | 22k | R_0402_1005Metric | R3 |
Esp gari - Copy design files
The KiCad project lives in the Vulcan758/My-PCB-Designs- repository on GitHub; these links point at the commit this page was built from.
Esp gari - Copy: common questions
What microcontroller does the Esp gari - Copy use?
The Esp gari - Copy is built around the ESP32-S3, from the ESP32 family.
How big is the Esp gari - Copy PCB?
The Esp gari - Copy measures 50.5 × 68.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Esp gari - Copy?
38 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp gari - Copy design files?
From the Vulcan758/My-PCB-Designs- repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp gari - Copy design in my own project?
The repository has no license, so all rights stay with Vulcan758. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp gari - Copy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in My-PCB-Designs-
AVR/Arduino
IR array sensor
Vulcan758
131.5 × 133.3 mm57 parts2LNo license0AVR/Arduino
IR array sensor - Copy
Vulcan758
113.5 × 138 mm57 parts2LNo license0ESP32
Saucey - Copy
Vulcan758
80.5 × 40.8 mm52 parts2LNo license0ESP32
Saucey
Vulcan758
74.5 × 41.3 mm48 parts2LNo license0ESP32
Esp gari
Vulcan758
50.5 × 63.9 mm38 parts4LNo license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k