Pocket-Potentiostat
yashil3·Pocket-Potentiostat·Potentiostat KiCAD Prohject/Potentiostat KiCAD Prohject.kicad_pcb
About the Pocket-Potentiostat PCB
Pocket-Potentiostat is an open source ESP32 PCB design by yashil3, published on GitHub. It is a 2-layer board measuring 121.9 × 55.9 mm, with 51 components from 28 distinct parts.
Its main chip is the ESP32-S2-SOLO, from the ESP32 family. Other key parts include the OPA2277, TL074, INA128, MCP4725xxx-xCH and REF3033. By type, the board carries 21 resistors, 12 ICs, 7 capacitors, 6 connectors, 2 switches and 2 diodes.
From the project
Potentiostat for applying cyclic voltammetry to electrolyte
- Blocks A, B, D, and E: uses OPA2277 high-precision operational amplifiers - Block C: uses TL074 transimpedance amplifier - Blocks F, G, and H: uses INA128 instrumentational amplifiers - Block C uses a TL074 Transimpedance Amplifier (TIA). It is cost-effective, but it is not the best option (a really good one would be ~$40) - May need to fix Rg resistor values based on how much the voltage in the electrodes varies
Main components on the Pocket-Potentiostat
Pocket-Potentiostat bill of materials (BOM)
51 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | OPA2277 | SOIC-8_3.9x4.9mm_P1.27mm | U1, U4 |
| 1 | TL074 | SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 3 | INA128 | SOIC-8_3.9x4.9mm_P1.27mm | U5, U7, U9 |
| 2 | MCP4725xxx-xCH | SOT-23-6 | U6, U11 |
| 1 | REF3033 | SOT-23 | U8 |
| 1 | ADS1115IDGS | TSSOP-10_3x3mm_P0.5mm | U10 |
| 1 | LD1117S33TR_SOT223 | SOT-223-3_TabPin2 | U13 |
| 1 | ESP32-S2-SOLO | ESP32-S2-SOLO | U14 |
| 2 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J1, J3 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
| 1 | Reference Electrode | CONN_575-8_KEY | J4 |
| 2 | Working Electrode | CONN_575-8_KEY | J5, J6 |
| 1 | DIPxx-1Axx-12xD | Relay_StandexMeder_DIP_LowProfile | K1 |
| 1 | Reset | SW_Push_1P1T-SH_NO_CK_KMR2xxG | SW1 |
| 1 | Boot | SW_Push_1P1T-SH_NO_CK_KMR2xxG | SW2 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 1 | 1N47xxA | D_DO-41_SOD81_P10.16mm_Horizontal | D2 |
| 1 | 0.47 uF | CAPC7851084X4N | C1 |
| 1 | 100nF | C_0603_1608Metric | C2 |
| 1 | 10uF | C_0603_1608Metric | C3 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | .1uF | C_0603_1608Metric | C4, C6, C7 |
| 1 | 1uF | C_0603_1608Metric | C5 |
| 1 | 4.12k | R_0603_1608Metric | R1 |
| 15 | 10k | R_0603_1608Metric | R2, R3, R4, R5, R6, R7, R8, R9 +7 |
| 1 | 470 | R_0603_1608Metric | R12 |
| 1 | 1M | R_0603_1608Metric | R14 |
| 1 | 5.23k | R_0603_1608Metric | R18 |
| 2 | 5.1 k | R_0603_1608Metric | R19, R20 |
Pocket-Potentiostat design files
The KiCad project lives in the yashil3/Pocket-Potentiostat repository on GitHub; these links point at the commit this page was built from.
Pocket-Potentiostat: common questions
What microcontroller does the Pocket-Potentiostat use?
The Pocket-Potentiostat is built around the ESP32-S2-SOLO, from the ESP32 family.
How big is the Pocket-Potentiostat PCB?
The Pocket-Potentiostat measures 121.9 × 55.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pocket-Potentiostat?
51 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pocket-Potentiostat design files?
From the yashil3/Pocket-Potentiostat repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pocket-Potentiostat design in my own project?
The repository has no license, so all rights stay with yashil3. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pocket-Potentiostat without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k