6 open source boards using the ESP32-S2-SOLO
Real designs built with the ESP32-S2-SOLO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Galvo
breqdev
200 × 50 mm84 parts2LNo license16ESP32
Iot leddriver hw
0xjmux
57 × 56 mm58 parts4LNo license9ESP32
Minimap
lucapoulos
48 × 55.4 mm74 parts4LNo license2ESP32
Hw thingcell
GuilleGonzzalez
32.5 × 67 mm81 parts4LNo license0ESP32
Pocket-Potentiostat
yashil3
121.9 × 55.9 mm51 parts2LNo license0ESP32
BigBrainFinal
ashvin-verma
87.6 × 73.4 mm43 parts2LNo license0
How designs wire the ESP32-S2-SOLO
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP32-S2-SOLO connects to, and the resistors, capacitors and other passives placed on it.
- The 3V3 pin is tied to 3.3V on 6 of 6 designs.
- The EN pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 470 Ω).
- The EN pin has a capacitor to GND on 5 of 6 designs, most often 100 nF.
- The MTDI/GPIO41/CLK_OUT1 pin is left unconnected on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 40, 41 | Connected to: GND 100% | — |
| 3V3pin 2 | Connected to: 3.3V 100% | — |
| ENpin 3 | Connected to: Signal 100% |
|
| GPIO15/U0RTS/ADC2_CH4/XTpin 8 | Connected to: Not connected 83% · a signal 17% | — |
| GPIO16/U0CTS/ADC2_CH5/XTpin 9 | Connected to: Not connected 83% · a signal 17% | — |
| GPIO18/U1RXD/ADC2_CH7/DApin 11 | Connected to: Not connected 67% · a signal 33% | — |
| GPIO3/TOUCH3/ADC1_CH2pin 15 | Connected to: Not connected 67% · a signal 33% | — |
| GPIO46pin 16 | Connected to: Not connected 83% · a signal 17% | — |
| GPIO9/TOUCH9/ADC1_CH8/FSpin 17 | Connected to: Signal 83% · not connected 17% |
|
| GPIO11/TOUCH11/ADC2_CH0/pin 19 | Connected to: Not connected 67% · a signal 33% | — |
| GPIO12/TOUCH12/ADC2_CH1/pin 20 | Connected to: Not connected 50% · a signal 50% |
|
| GPIO13/TOUCH13/ADC2_CH2/pin 21 | Connected to: Not connected 67% · a signal 33% |
|
| GPIO14/TOUCH14/ADC2_CH3/pin 22 | Connected to: Not connected 67% · a signal 33% |
|
| GPIO21pin 23 | Connected to: Not connected 67% · a signal 33% | — |
| SPIIO4/GPIO33/FSPIHDpin 24 | Connected to: Not connected 83% · a signal 17% | — |
| GPIO45pin 26 | Connected to: Not connected 67% · a signal 33% | — |
| GPIO0pin 27 | Connected to: Signal 100% |
|
| SPIDQS/GPIO37/FSPIQpin 30 | Connected to: Not connected 67% · a signal 33% | — |
| GPIO38/FSPIWPpin 31 | Connected to: Not connected 83% · a signal 17% | — |
| MTCK/GPIO39/CLK_OUT3pin 32 | Connected to: Not connected 83% · a signal 17% | — |
| MTDO/GPIO40/CLK_OUT2pin 33 | Connected to: Not connected 83% · a signal 17% | — |
| MTDI/GPIO41/CLK_OUT1pin 34 | Connected to: Not connected 100% | — |
| MTMS/GPIO42pin 35 | Connected to: Not connected 100% | — |
| GPIO2/TOUCH2/ADC1_CH1pin 38 | Connected to: Not connected 50% · a signal 50% |
|
15 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Galvo by breqdev, Iot leddriver hw by 0xjmux, Minimap by lucapoulos and BigBrainFinal by ashvin-verma.
The ESP32-S2-SOLO in open source designs
The gallery holds 6 open source boards using the ESP32-S2-SOLO from 6 GitHub repositories; a typical one measures about 72.3 × 55.9 mm and carries around 66 components.
50% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Galvo by breqdev.
Microcontrollers on boards using the ESP32-S2-SOLO
What boards using the ESP32-S2-SOLO are built for
ESP32-S2-SOLO: common questions
Where can I find a ESP32-S2-SOLO reference design?
Each of the 6 boards on this page is a real design using the ESP32-S2-SOLO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32-S2-SOLO 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-S2-SOLO.
What pull-up resistor is used on the ESP32-S2-SOLO EN pin?
The EN pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 470 Ω). Counted from the KiCad layouts of 6 open source designs using the ESP32-S2-SOLO.
How is the ESP32-S2-SOLO MTDI/GPIO41/CLK_OUT1 pin connected?
The MTDI/GPIO41/CLK_OUT1 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-S2-SOLO.
Which microcontrollers do boards using the ESP32-S2-SOLO use?
Most are built on ESP32 (6).
How big is a typical board using the ESP32-S2-SOLO?
The median is 72.3 × 55.9 mm, and 50% are two-layer designs.
What is the most popular open source board using the ESP32-S2-SOLO?
By GitHub stars, Galvo by breqdev, with 16 stars.
Can I simulate one of these boards using the ESP32-S2-SOLO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.