12 open source boards using the INA128
Real designs built with the INA128, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Osciloscope-ESP32
cristobalcuevas
137.5 × 42.5 mm79 parts2LNo license4STM32
CPU Board
jsjolund
100 × 70 mm112 parts2LNo license3Electronic-Stethescope
shreenandansonu
85 × 55 mm54 parts2LMIT3Modular Filter
TZeng0698
35 × 22.2 mm38 parts2LNo license3Fonte corrente bipolar V01
Pinheirogustavo
90 × 100 mm56 parts2LNo license2Svm
lucia3e8
148 × 38.5 mm44 parts2LNo license1STM32
MR71 ESR METER
7961
90 × 93 mm131 parts4LNo license0ESP32
Pocket-Potentiostat
yashil3
121.9 × 55.9 mm51 parts2LNo license0Eda design simulation portfolio
katherinejenniferhsfeemster
50 × 27.5 mm2 parts2LNo license0Rogowski
eauel
88 × 94 mm17 parts2LGPL-3.00Fonte corrente mono V02
Pinheirogustavo
90 × 100 mm39 parts2LNo license2.sensor oxigeno
CV19CO
29 × 29.5 mm9 parts4LCERN-OHL-P-2.05
How designs wire the INA128
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the INA128 connects to, and the resistors, capacitors and other passives placed on it.
- The RG pins have a series resistor on 9 of 10 designs, most often 100 kΩ (then 5 kΩ).
- The V- pin is tied to GND on 6 of 10 designs (-9V on 3).
- Pin 6 has a series resistor on 5 of 10 designs, most often 10 kΩ (then 200 kΩ).
- The - pin has a series resistor on 4 of 10 designs, most often 11.3 kΩ (then 10 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RGpin 1, 8 | Connected to: Signal 85% |
|
| -pin 2 | Connected to: A connector 50% |
|
| +pin 3 | Connected to: A connector 40% |
|
| V-pin 4 | Connected to: GND 60% · -9V 30% | — |
| Pin 6 | Connected to: A connector 20% |
|
| V+pin 7 | Connected to: 5V 80% · a signal 20% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include .sensor oxigeno by CV19CO, Osciloscope-ESP32 by cristobalcuevas, CPU Board by jsjolund and Electronic-Stethescope by shreenandansonu.
The INA128 in open source designs
The gallery holds 12 open source boards using the INA128 from 11 GitHub repositories; a typical one measures about 90 × 55.4 mm and carries around 48 components.
83% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is .sensor oxigeno by CV19CO.
Parts used alongside the INA128
What boards using the INA128 are built for
INA128: common questions
Where can I find a INA128 reference design?
Each of the 12 boards on this page is a real design using the INA128. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA128 RG pin?
The RG pins have a series resistor on 9 of 10 designs, most often 100 kΩ (then 5 kΩ). Counted from the KiCad layouts of 10 open source designs using the INA128.
How is the INA128 V- pin connected?
The V- pin is tied to GND on 6 of 10 designs (-9V on 3). Counted from the KiCad layouts of 10 open source designs using the INA128.
What resistor goes on the INA128 pin 6?
Pin 6 has a series resistor on 5 of 10 designs, most often 10 kΩ (then 200 kΩ). Counted from the KiCad layouts of 10 open source designs using the INA128.
Which microcontrollers do boards using the INA128 use?
Most are built on ESP32 (2) and STM32 (2).
How big is a typical board using the INA128?
The median is 90 × 55.4 mm, and 83% are two-layer designs.
What is the most popular open source board using the INA128?
By GitHub stars, .sensor oxigeno by CV19CO, with 5 stars.
Can I simulate one of these boards using the INA128 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.