ESP32 FC

JS2028EE·ESP32_FC·hardware/revB/ESP32_FC.kicad_pcb

ESP32 FC PCB layout, top view — open source ESP32 board by JS2028EE

About the ESP32 FC PCB

ESP32 FC is an open source ESP32 PCB design by JS2028EE, published on GitHub. It is a 4-layer board measuring 70 × 65 mm, with 103 components from 51 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the USBLC6-2SC6, LMR36510ADDAR, AP63203WU-7, TLV75533PDBVR and BMI088. By type, the board carries 46 resistors, 27 capacitors, 10 connectors, 8 ICs, 4 diodes and 3 transistors.

It belongs with the power & battery and sensors designs in this gallery.

From the project

This is the current editable KiCad 10 project for a 70 x 65 mm, four-layer controller, with an ESP32-S3-WROOM-1-N8R8, BMI088 SPI IMU, BMP280 barometer and a separate 4-in-1 ESC. The FC supply accepts a 3S-6S LiPo (9-25.2 V). Motor current stays on the ESC.

This is the current editable KiCad 10 project for a 70 x 65 mm, four-layer controller, with an ESP32-S3-WROOM-1-N8R8, BMI088 SPI IMU, BMP280 barometer and a separate 4-in-1 ESC. The FC supply accepts a 3S-6S LiPo (9-25.2 V). Motor current stays on the ESC.

Order status: prepared for a small bare-board prototype run to OrderInstructions.md.** This is an unbuilt design, not validated flight hardware. KiCad checks and the source/PCB audit pass. The manufacturer still must accept the uploaded fabrication data and requested stackup through its normal DFM process. Physical regulator, USB, sensor…

Main components on the ESP32 FC

ESP32 FC bill of materials (BOM)

103 components, 51 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N8R8
U1
1
USBLC6-2SC6
U2
1
LMR36510ADDAR
U3
1
AP63203WU-7
U4
1
TLV75533PDBVR
U5
1
BMI088
U6
1
BMP280
U7
1
SN74LVC125APWR
U8
3
DMN2056U-7
DMN2056U
Q1, Q2, Q3
1
TYPE-C-31-M-12
USB-C / USB2 FS
J1
1
WIRE CONNECTION - NO FITTED PART
BATTERY 3S-6S
J2
1
TSW-104-07-G-S
I2C / 3.3V ONLY
J3
1
TSW-102-07-G-S
KILL STRAP
J4
1
TSW-108-07-G-S
4-IN-1 ESC
J5
1
TSW-104-07-G-S
CRSF RECEIVER
J6
1
TSW-104-07-G-S
GPS UART
J7
1
TSW-104-07-G-S
DEBUG UART0
J8
1
TSW-104-07-G-S
AUX GPIO / TELEMETRY
J9
1
TSW-102-07-G-S
ACTIVE BUZZER
J10
1
0476001.MR
1A / 476
F1
Show 31 more
QtyPartRefs
1
TL3342F160QG
RESET
SW1
1
TL3342F160QG
BOOT
SW2
1
SS310-13-F
SS310 / 100V 3A
D1
1
SMBJ28A-13-F
SMBJ28A
D2
1
APT1608LZGCK
GREEN
D3
1
1N4148W-7-F
1N4148W
D4
1
SRP6060FA-220M
22uH
L1
1
SRP5030T-4R7M
4.7uH
L2
4
GRM21BR61C226ME44L
22u
C1, C13, C15, C16
11
GRM188R71C104KA01D
100n
C2, C4, C10, C14, C19, C20, C22, C23 +3
2
GRM188R71C105KA12D
1u
C3, C17
1
GRM188R71H103KA01D
10n
C5
2
GRM32ER72A225KA35L
2.2u / 100V
C6, C7
1
C0805C224K1RACTU
220n / 100V
C8
1
GRM188R71C105KA12D
1u / 16V
C9
2
GRM32ER71E226KE15L
22u / 25V
C11, C12
2
GRM188R61C475KE11D
4.7u
C18, C21
1
EEUFR1H470
47u / 50V
C27
12
RC0603FR-0710KL
10k
R1, R2, R3, R4, R9, R17, R18, R23 +4
2
RC0603FR-0722RL
22R
R5, R6
2
RC0603FR-075K1L
5.1k
R7, R8
3
RC0603FR-07100KL
100k
R10, R35, R44
1
RC0603FR-0780K6L
80.6k
R11
1
RC0603FR-0720KL
20k
R12
8
RC0603FR-0733RL
33R
R13, R14, R15, R16, R25, R26, R27, R28
2
RC0603FR-074K7L
4.7k
R19, R20
1
RT0603BRD07150KL
150k
R21
1
RT0603BRD0710KL
10k
R22
4
RC0603FR-0747KL
47k
R29, R30, R31, R32
7
RC0603FR-071KL
1k
R34, R36, R37, R39, R41, R42, R43
2
RC0603FR-07100RL
100R
R38, R40

ESP32 FC design files

The KiCad project lives in the JS2028EE/ESP32_FC repository on GitHub; these links point at the commit this page was built from.

ESP32 FC: common questions

What microcontroller does the ESP32 FC use?

The ESP32 FC is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.

How big is the ESP32 FC PCB?

The ESP32 FC measures 70 × 65 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the ESP32 FC?

103 components, from 51 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ESP32 FC design files?

From the JS2028EE/ESP32_FC repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ESP32 FC design in my own project?

The repository has no license, so all rights stay with JS2028EE. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the ESP32 FC without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards