Homebrew 486
kanaboid·elektronika·mainboard/M8SBC-486/pcb/homebrew_486.kicad_pcb
About the Homebrew 486 PCB
Homebrew 486 is an open source ESP32 PCB design by kanaboid, published on GitHub. It is a 4-layer board measuring 150 × 150 mm, with 123 components from 69 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the W25Q128JVS, MCP73831-2-OT, AMS1117-3.3, 74LS245 and 8254. By type, the board carries 42 capacitors, 29 resistors, 23 ICs, 22 connectors, 3 crystals and 2 switches.
From the project
M8SBC-486 KiCad 9.0 schematic. Current revision: 1.01
M8SBC-486 KiCad 9.0 schematic. Current revision: 1.01
Used fonts: Ac437 IBM VGA 8x16 and URW Gothic
- 486 Socket symbol & footprint: ciprian-stingu/KiCad-486-CPU-socket - Mini DIN-6 connector with shielding footprint: 4x1md/kicad_libraries - 16-bit ISA slot footprint: the retro web / Aries-1 - PCBWay for manufacturing boards!
Main components on the Homebrew 486
Homebrew 486 bill of materials (BOM)
123 components, 69 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 486Socket | 486Socket | U1 |
| 1 | W25Q128JVS XC2S100TQ144 | TQFP-144_20x20mm_P0.5mm | U2 |
| 1 | MCP73831-2-OT AMS1117 | SOT-223-3_TabPin2 | U3 |
| 1 | AMS1117-3.3 AMS1117 | SOT-223-3_TabPin2 | U4 |
| 6 | 74LS245 | SOP-20_7.5x12.8mm_P1.27mm | U5, U6, U7, U8, U19, U20 |
| 1 | 8254 | DIP-24_W15.24mm | U9 |
| 1 | 8259A-2 | PLCC-28_THT-Socket | U10 |
| 8 | HM628512 | SOP-32_11.305x20.495mm_P1.27mm | U11, U12, U13, U14, U15, U16, U17, U18 |
| 1 | W29C020 | DIP-32_W15.24mm | U21 |
| 1 | ATmega128L-8A | TQFP-64_14x14mm_P0.8mm | U22 |
| 1 | 74LS573 | SOP-20_7.5x12.8mm_P1.27mm | U23 |
| 1 | TXC-7C | Oscillator_SMD_SeikoEpson_SG8002CA-4Pin_7.0x5.0mm_HandSoldering | Y1 |
| 1 | GTXO-14T | Oscillator_DIP-14 | Y2 |
| 1 | 16MHz | Crystal_HC49-4H_Vertical | Y3 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P Bus_ISA_16bit | ISA16 | J1 |
| 1 | CONN_01X02_PIN Bus_ISA_16bit | ISA16 | J2 |
| 1 | CONN_01X18_PIN ATX-20 | Molex_Mini-Fit_Jr_5566-20A_2x10_P4.20mm_Vertical | J3 |
| 1 | AVR ISP | PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | CONN_01X18_PIN FPGA JTAG | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Enable load | PinHeader_1x02_P2.54mm_Vertical | J6 |
Show 49 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RAM cacheable | PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | ROM cacheable | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | CLKMUL SET | PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | ISA_DEBUG | PinHeader_1x10_P2.54mm_Vertical | J10 |
| 1 | PEN | PinHeader_1x01_P2.54mm_Vertical | J11 |
| 1 | MEM_WR_RD_J | PinHeader_1x02_P2.54mm_Vertical | J12 |
| 1 | KB | Connector_Mini-DIN_Female_6Pin_2rows | J13 |
| 1 | ATMegaSpare | PinHeader_1x06_P2.54mm_Vertical | J14 |
| 1 | PC SPK | PinHeader_1x04_P2.54mm_Vertical | J15 |
| 1 | ATUART | PinHeader_1x03_P2.54mm_Vertical | J16 |
| 1 | IOout | PinHeader_1x06_P2.54mm_Vertical | J17 |
| 1 | Reset ext | PinHeader_1x02_P2.54mm_Vertical | J18 |
| 4 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J19, J20, J21, J22 |
| 1 | SW_SPDT | PinHeader_1x03_P2.54mm_Vertical | SW1 |
| 1 | Reset btn | SW_PUSH_6mm | SW2 |
| 1 | PWR_LED | LED_D4.0mm | D1 |
| 1 | D7_LED | LED_D4.0mm | D2 |
| 1 | 22u | CP_Radial_D5.0mm_P2.50mm | C1 |
| 1 | 10UF 22u | CP_Radial_D5.0mm_P2.50mm | C2 |
| 7 | 10UF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C7, C8, C16, C17, C20, C25 |
| 2 | 12PF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C33 |
| 1 | 22p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 10UF 22p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 13 | 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C12, C14, C21, C23, C24, C27, C28 +5 |
| 8 | 0.1UF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C11, C15, C18, C19, C22, C32, C35 |
| 2 | 1UF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13, C26 |
| 1 | 15PF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C31 |
| 1 | 10UF 10u | CP_Radial_D5.0mm_P2.50mm | C36 |
| 2 | 12PF 10u | CP_Radial_D5.0mm_P2.50mm | C37, C38 |
| 1 | 1UF 10u | CP_Radial_D5.0mm_P2.50mm | C39 |
| 1 | 10NF 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C40 |
| 2 | 4.7K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3 |
| 1 | 33R 4.7K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 10K 4.7K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 3 | 120 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R7 |
| 1 | 200 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 5 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R11, R13, R27, R28 |
| 1 | 33 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 200K 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 5.1K 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14 |
| 2 | 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15, R23 |
| 3 | 470R 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16, R24, R25 |
| 1 | 5.1K 300 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
| 1 | 33R 300 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18 |
| 1 | 200K 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 100K 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R20 |
| 2 | 10K 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R22 |
| 1 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R26 |
| 1 | 10 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R29 |
Homebrew 486 design files
The KiCad project lives in the kanaboid/elektronika repository on GitHub; these links point at the commit this page was built from.
Homebrew 486: common questions
What microcontroller does the Homebrew 486 use?
The Homebrew 486 is built around the ESP32-S3, from the ESP32 family.
How big is the Homebrew 486 PCB?
The Homebrew 486 measures 150 × 150 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Homebrew 486?
123 components, from 69 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Homebrew 486 design files?
From the kanaboid/elektronika repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Homebrew 486 design in my own project?
The repository has no license, so all rights stay with kanaboid. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Homebrew 486 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in elektronika
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k