7 open source boards using the 8254
Real designs built with the 8254, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
M8SBC-486
maniekx86
150 × 150 mm123 parts4LNo license253- schematic only · 207 parts
DeskPro386 16
breadboardinglabs
207 partsMIT4 Z80 IOB
kuninet
100 × 74.9 mm34 parts2LMIT2AVR/Arduino
MDA80486SBC Final
mattheeewahn
150 × 150 mm123 parts4LGPL-3.01MUTIF09 Single Board Computer
ja1umi
155 × 114 mm68 parts2LMIT10ChargeBoard
Envious-Data
24.8 × 65 mm49 parts2LGPL-3.01ESP32
Homebrew 486
kanaboid
150 × 150 mm123 parts4LNo license0
How designs wire the 8254
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 8254 connects to, and the resistors, capacitors and other passives placed on it.
- The G0 pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The G1 pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The OUT0 pin has a pull-up to 5V on 3 of 6 designs, most often 1 kΩ.
- The OUT2 pin has a series resistor on 3 of 6 designs, most often 33 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT0pin 10 | Connected to: 8259A-2 50% |
|
| G0pin 11 | Connected to: 5V 67% · a signal 33% | — |
| GNDpin 12 | Connected to: GND 100% | — |
| G1pin 14 | Connected to: 5V 67% · a signal 33% | — |
| OUT2pin 17 | Connected to: Signal 67% · not connected 33% |
|
| VCCpin 24 | Connected to: 5V 100% | — |
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M8SBC-486 by maniekx86, MUTIF09 Single Board Computer by ja1umi, Z80 IOB by kuninet and ChargeBoard by Envious-Data.
The 8254 in open source designs
The gallery holds 7 open source boards using the 8254 from 7 GitHub repositories; a typical one measures about 150 × 132 mm and carries around 123 components.
50% are two-layer designs, the rest use four layers or more, and 71% carry an open source license.
The most starred is M8SBC-486 by maniekx86.
Parts used alongside the 8254
Microcontrollers on boards using the 8254
What boards using the 8254 are built for
8254: common questions
Where can I find a 8254 reference design?
Each of the 7 boards on this page is a real design using the 8254. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 8254 G0 pin connected?
The G0 pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the 8254.
How is the 8254 G1 pin connected?
The G1 pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the 8254.
What pull-up resistor is used on the 8254 OUT0 pin?
The OUT0 pin has a pull-up to 5V on 3 of 6 designs, most often 1 kΩ. Counted from the KiCad layouts of 6 open source designs using the 8254.
What parts are used alongside the 8254?
The 74LS245, 8259A-2, 74LS573, ATmega128L-8A and HM628512 appear in the most repositories here.
Which microcontrollers do boards using the 8254 use?
Most are built on AVR/Arduino (2) and ESP32 (1).
How big is a typical board using the 8254?
The median is 150 × 132 mm, and 50% are two-layer designs.
What is the most popular open source board using the 8254?
By GitHub stars, M8SBC-486 by maniekx86, with 253 stars.
Can I simulate one of these boards using the 8254 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.