Battery monitor

kaushalch1·battery-monitor·pcb,gerber files/pcb filess/battery monitor.kicad_pcb

Battery monitor PCB layout, top view — open source ESP32 board by kaushalch1

About the Battery monitor PCB

Battery monitor is an open source ESP32 PCB design by kaushalch1, published on GitHub. It is a 2-layer board measuring 134.5 × 87 mm, with 55 components from 34 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6, LM358, TPS63020DSJR, INA226 and B4B-XH-A(LF)(SN). By type, the board carries 21 resistors, 9 ICs, 6 switches, 6 capacitors, 3 transistors and 3 connectors.

It belongs with the power & battery, iot & wireless and displays & leds designs in this gallery.

From the project

CellCheck is a battery discharge analyzer designed to measure battery voltage, current, power, temperature, estimated capacity, energy, and approximate internal resistance.

CellCheck is a battery discharge analyzer designed to measure battery voltage, current, power, temperature, estimated capacity, energy, and approximate internal resistance.

the planned hardware supports interchangeable holders for single 18650 Li ion cells and AA/AAA NiMH/NiCd cells. It uses an esp32-s3 controller, an oled dashboard, usb serial communication, and a protected programmable electronic load.

Battery monitor, from the project README
From the project README

Main components on the Battery monitor

Battery monitor bill of materials (BOM)

55 components, 34 distinct parts.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
USBLC6-2SC6
U2
1
LM358
U3
1
TPS63020DSJR
TI(德州仪器)
U4
1
INA226
U5
1
B4B-XH-A(LF)(SN)
B4B-XH-A
JST
U6
1
MCP9808_DFN
U7
1
LM397
U8
1
ER_OLEDM0.91_1x-I2C
U9
1
Q_PMOS_GSD
Q1
2
Q_NMOS_GSD
Q2, Q3
1
USB_C_Receptacle_USB2.0_16P
J1
1
Conn_01x02
J2
1
Conn_01x02_Pin
J3
1
BH-AA-A5BJ012
MYOUNG(美阳)
B1
1
BH-18650-A1AJ006
MYOUNG(美阳)
BT1
1
Fuse
F1
2
SW_Push
SW1, SW2
1
SW_DPDT_x2
SW3
3
SW_Push
SW4, SW5, SW6
Show 14 more
QtyPartRefs
1
10k
TH1
2
LED
D1, D2
1
1.5u
L1
3
10u
C1, C2, C5
3
100n
C3, C4, C6
2
5.1k
R1, R2
7
10k
R3, R9, R15, R16, R19, R20, R21
3
100k
R4, R5, R6
1
0.22
R7
1
220
R8
3
4.7k
R10, R12, R13
1
0.02
R11
1
2.4k
R14
2
1k
R17, R18

Battery monitor design files

The KiCad project lives in the kaushalch1/battery-monitor repository on GitHub; these links point at the commit this page was built from.

Battery monitor: common questions

What microcontroller does the Battery monitor use?

The Battery monitor is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Battery monitor PCB?

The Battery monitor measures 134.5 × 87 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Battery monitor?

55 components, from 34 distinct parts. The full bill of materials is listed on this page.

Where can I download the Battery monitor design files?

From the kaushalch1/battery-monitor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Battery monitor design in my own project?

The repository has no license, so all rights stay with kaushalch1. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Battery monitor without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards