16 open source boards using the LM397
Real designs built with the LM397, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Custom BMS
SCFormulaElectric
104.2 × 59.7 mm192 parts4LNo license9ESP8266
PixelFan LedLeiste
C3MA
343.3 × 297.3 mm160 parts2LNo license1AVR/Arduino
Control panel
lucanastasio
65 × 58 mm158 parts2LNo license1ESP32
Battery monitor
kaushalch1
134.5 × 87 mm55 parts2LNo license0RP2040/RP2350
Uswc
crides
27.5 × 24 mm44 parts2LNo license0SCS Interface
JavaPowerFR
42 × 48.7 mm38 parts2LMIT0- schematic only · 58 partsAVR/Arduino
Voltmeter
wolly981
58 partsNo license0 - schematic only · 18 parts
Pr fschaltungen
backforthelag
18 partsNo license0 STM32
Enepaq TempSensor Board
SCFormulaElectric
68.9 × 129.2 mm157 parts4LNo license9ESP8266
PixelFan
C3MA
110 × 110 mm63 parts2LNo license1SCS Interface Lte
JavaPowerFR
21.7 × 43.7 mm24 parts2LMIT0STM32
ETS Board Copy
SCFormulaElectric
68.9 × 129.2 mm157 parts4LNo license9Prechargedischarge mkviii
olin-electric-motorsports
158.4 × 109.4 mm87 parts2LMIT13BPSD-2025
LSUTigerRacing
68.5 × 43 mm50 parts2LNo license7TemperatureMonitor
89Mods
25.9 × 11.2 mm10 parts2LMIT2STM32
BSPD 5
SCFormulaElectric
40.1 × 54.3 mm24 parts2LNo license9
How designs wire the LM397
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LM397 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 6 of 9 designs (a signal on 2).
- The 2Y pin has a pull-up to 5V on 5 of 9 designs, most often 10 kΩ (then 100 kΩ).
- The V+ pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF (then 1 µF).
- The + pin has a resistor to GND on 4 of 9 designs, most often 100 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| -pin 1 | Connected to: Signal 78% · 0.385V 22% |
|
| V-pin 2 | Connected to: GND 67% · a signal 22% | — |
| +pin 3 | Connected to: Signal 78% · not connected 22% |
|
| 2Ypin 4 | Connected to: Signal 89% |
|
| V+pin 5 | Connected to: 5V 78% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Prechargedischarge mkviii by olin-electric-motorsports, BSPD 5 by SCFormulaElectric, BPSD-2025 by LSUTigerRacing and TemperatureMonitor by 89Mods.
The LM397 in open source designs
The gallery holds 16 open source boards using the LM397 from 11 GitHub repositories; a typical one measures about 68.7 × 58.8 mm and carries around 57 components.
79% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Prechargedischarge mkviii by olin-electric-motorsports.
Microcontrollers on boards using the LM397
What boards using the LM397 are built for
LM397: common questions
Where can I find a LM397 reference design?
Each of the 16 boards on this page is a real design using the LM397. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM397 V- pin connected?
The V- pin is tied to GND on 6 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the LM397.
What pull-up resistor is used on the LM397 2Y pin?
The 2Y pin has a pull-up to 5V on 5 of 9 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 9 open source designs using the LM397.
What decoupling capacitors do designs use on the LM397 V+ pin?
The V+ pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the LM397.
Which microcontrollers do boards using the LM397 use?
Most are built on STM32 (4), AVR/Arduino (2), ESP8266 (2) and ESP32 (1).
How big is a typical board using the LM397?
The median is 68.7 × 58.8 mm, and 79% are two-layer designs.
What is the most popular open source board using the LM397?
By GitHub stars, Prechargedischarge mkviii by olin-electric-motorsports, with 13 stars.
Can I simulate one of these boards using the LM397 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.