Plant-Health-Meter

MarkusVLA·Plant-Health-Meter·PCB/Plant-health-meter.kicad_pcb

Plant-Health-Meter PCB layout, top view — open source ESP32 board by MarkusVLA

About the Plant-Health-Meter PCB

Plant-Health-Meter is an open source ESP32 PCB design by MarkusVLA, published on GitHub under the MIT license. It is a 4-layer board measuring 136.2 × 25 mm, with 94 components from 46 distinct parts.

Its main chip is the ESP32-C3FH4X, from the ESP32 family. Other key parts include the TP4057, TPS61022, USBLC6-2P6, LTC4412XS6 and TPS62172DSG. By type, the board carries 32 capacitors, 24 resistors, 10 ICs, 10 diodes, 7 connectors and 5 inductors.

It belongs with the iot & wireless and sensors designs in this gallery.

From the project

1. By default, there are no Wi-Fi credentials set. The device will immediately enter Bluetooth setup mode on boot.

1. By default, there are no Wi-Fi credentials set. The device will immediately enter Bluetooth setup mode on boot.

2. For setup, you’ll need a mobile app capable of sending data over BLE, such as nRF Connect.

3. When the device is in Bluetooth setup mode, one of its LEDs will begin blinking. You can then find the device in the app under the name: PLANTSENSOR01

Plant-Health-Meter, from the project README
From the project README

Main components on the Plant-Health-Meter

Plant-Health-Meter bill of materials (BOM)

94 components, 46 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TP4057
U1
1
TPS61022
U2
1
USBLC6-2P6
U3
1
LTC4412XS6
LTC4412xS6
U4
1
TPS62172DSG
U5
1
ESP32-C3FH4X
U6
1
OPA340NA
U7
1
BME280
U8
1
ADS1115IDGS
U9
1
TCA9555RTWR
U10
1
AO3401A
Q1
1
40MHZ
40MHz
Y1
5
CONN_01X02
Conn_01x02
J1, J2, J3, J4, J6
1
USB_C_RECEPTACLE_USB2.0_14P
USB_C_Receptacle_USB2.0_14P
J5
1
CONN_02X08_COUNTER_CLOCKWISE
Conn_02x08_Counter_Clockwise
J7
1
Antenna_Shield
AE1
1
~
S1
1
C115357
Boot
SW1
1
C115357
Reset
SW2
4
LED
D1, D2, D5, D6
Show 26 more
QtyPartRefs
3
ESD9B5.0ST5G
D3, D7, D8
1
BAT60A
D4
1
BPW34-SMD
D9
1
BAT54J
D10
1
1u
L1
1
2.2N
2.2n
L2
1
2.2U
2.2u
L3
1
2.2N
2.2n
L4
1
2.6N
2.6n
L5
6
10U
10u
C1, C2, C6, C7, C12, C16
18
100N
100n
C3, C5, C9, C13, C14, C15, C17, C19 +10
2
22U
22u
C4, C8
2
15P
15p
C10, C11
2
2.2P
2.2p
C18, C20
1
220N
220n
C25
1
1n
C28
3
1k
R1, R10, R11
8
5.1K
5.1k
R2, R3, R5, R12, R14, R15, R16, R17
2
10K
10k
R4, R20
1
570K
570k
R6
4
100K
100k
R7, R9, R23, R24
1
470K
470k
R8
1
10
R13
1
33K
33k
R18
2
510
R19, R22
1
1M
R21

Plant-Health-Meter design files

The KiCad project lives in the MarkusVLA/Plant-Health-Meter repository on GitHub; these links point at the commit this page was built from.

Plant-Health-Meter: common questions

What microcontroller does the Plant-Health-Meter use?

The Plant-Health-Meter is built around the ESP32-C3FH4X, from the ESP32 family.

How big is the Plant-Health-Meter PCB?

The Plant-Health-Meter measures 136.2 × 25 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Plant-Health-Meter?

94 components, from 46 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Plant-Health-Meter design files?

From the MarkusVLA/Plant-Health-Meter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Plant-Health-Meter design in my own project?

Yes, under the terms of its MIT license, which MarkusVLA chose for the repository.

Can I test firmware for the Plant-Health-Meter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards