9 open source boards using the TPS62172DSG
Real designs built with the TPS62172DSG, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
F8-fc h7 rev a
victorhook
35.5 × 35.5 mm105 parts4LNo license6STM32
Vesc
LJBoxx
61.5 × 60 mm196 parts4LCERN-OHL-S-2.05- schematic only · 192 partsFPGA
NetStream-Caravel
adulu-bang
192 partsApache-2.03 ESP32
Plant-Health-Meter
MarkusVLA
136.2 × 25 mm94 parts4LMIT2Flight computer
unl-rocketry
27 × 60 mm32 parts2LCERN-OHL-S-2.01EEE3088F-Project-2025-Group-37
AnnaLukose
59 × 70 mm63 parts2LNo license0STM32
F8-fc rev a
victorhook
35.5 × 35.5 mm105 parts4LNo license6STM32
Logic
LJBoxx
60.5 × 60.7 mm151 parts4LCERN-OHL-S-2.05STM32
Stm32-nema17-servo
dognotdog
48 × 44.5 mm93 parts4LCustom license5
How designs wire the TPS62172DSG
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS62172DSG connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 10 µH).
- The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 10 µF.
- The FB pin is tied to GND on 6 of 6 designs.
- The VOS pin has a inductor on 5 of 6 designs, most often 2.2 µH.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PGNDpin 1 | Connected to: GND 100% | — |
| VINpin 2 | Connected to: VSYS 67% · a signal 33% |
|
| ENpin 3 | Connected to: VSYS 67% · a signal 33% | — |
| AGNDpin 4 | Connected to: GND 100% | — |
| FBpin 5 | Connected to: GND 100% | — |
| VOSpin 6 | Connected to: 3.3V 67% · a signal 33% |
|
| SWpin 7 | Connected to: Signal 100% |
|
| PGpin 8 | Connected to: Signal 83% · not connected 17% |
|
| PADpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include F8-fc h7 rev a by victorhook, Stm32-nema17-servo by dognotdog, Logic by LJBoxx and Plant-Health-Meter by MarkusVLA.
The TPS62172DSG in open source designs
The gallery holds 9 open source boards using the TPS62172DSG from 7 GitHub repositories; a typical one measures about 53.5 × 52.3 mm and carries around 105 components.
75% use four copper layers or more, and 56% carry an open source license.
The most starred is F8-fc h7 rev a by victorhook.
Parts used alongside the TPS62172DSG
What boards using the TPS62172DSG are built for
TPS62172DSG: common questions
Where can I find a TPS62172DSG reference design?
Each of the 9 boards on this page is a real design using the TPS62172DSG. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS62172DSG SW pin connected?
The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 10 µH). Counted from the KiCad layouts of 6 open source designs using the TPS62172DSG.
What decoupling capacitors do designs use on the TPS62172DSG VIN pin?
The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 10 µF. Counted from the KiCad layouts of 6 open source designs using the TPS62172DSG.
How is the TPS62172DSG FB pin connected?
The FB pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TPS62172DSG.
Which microcontrollers do boards using the TPS62172DSG use?
Most are built on STM32 (5), ESP32 (1) and FPGA (1).
How big is a typical board using the TPS62172DSG?
The median is 53.5 × 52.3 mm, and 25% are two-layer designs.
What is the most popular open source board using the TPS62172DSG?
By GitHub stars, F8-fc h7 rev a by victorhook, with 6 stars.
Can I simulate one of these boards using the TPS62172DSG before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.