10 open source boards using the TPS61022
Real designs built with the TPS61022, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Powerbank
k-off
17.9 × 64.9 mm30 parts2LApache-2.04ESP32
Plant-Health-Meter
MarkusVLA
136.2 × 25 mm94 parts4LMIT2AVR/Arduino
Pi super ups
mairas
65 × 56 mm86 parts2LBSD-3-Clause2RP2040/RP2350
LitterWatch
bluetiger9
142 × 102 mm76 parts4LNo license2AVR/Arduino
VoidLens-DIY-VR-Headset-V2
scattercat-123
44.4 × 60.3 mm79 parts2LNo license1ESP32
Lamp-2
DodoZimmermann
147 × 139.9 mm248 parts6LMIT0STM32
--MagneticField---Acceleration-Sensors
ahoang205
76.1 × 74.9 mm92 parts2LMIT0RP2040/RP2350
TixClock
vinnesttree
38.1 × 133.4 mm85 parts2LMIT0STM32
Pendant
picafe
33.2 × 33.2 mm45 parts4LNo license0ESP32
Panic button tiny
HenraL
38.2 × 38.3 mm16 parts2LMIT0
How designs wire the TPS61022
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TPS61022 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 9 of 9 designs, most often 1 µH.
- The VOUT pin has a decoupling capacitor on 9 of 9 designs, most often 22 µF (then 10 µF).
- The FB pin has a resistor to GND on 9 of 9 designs, most often 100 kΩ (then 43 kΩ).
- The VIN pin has a inductor on 7 of 9 designs, most often 1 µH.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 100% |
|
| VOUTpin 3 | Connected to: 5V 56% · a signal 44% |
|
| FBpin 4 | Connected to: Signal 100% |
|
| ENpin 5 | Connected to: The microcontroller 33% · BATT 44% |
|
| MODEpin 6 | Connected to: GND 67% · BATT 22% |
|
| VINpin 7 | Connected to: BATT 78% · a signal 22% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Powerbank by k-off, LitterWatch by bluetiger9, Pi super ups by mairas and Plant-Health-Meter by MarkusVLA.
The TPS61022 in open source designs
The gallery holds 10 open source boards using the TPS61022 from 10 GitHub repositories; a typical one measures about 54.7 × 62.6 mm and carries around 82 components.
60% are two-layer designs, the rest use four layers or more, and 70% carry an open source license.
The most starred is Powerbank by k-off.
Parts used alongside the TPS61022
Microcontrollers on boards using the TPS61022
What boards using the TPS61022 are built for
TPS61022: common questions
Where can I find a TPS61022 reference design?
Each of the 10 boards on this page is a real design using the TPS61022. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS61022 SW pin connected?
The SW pin has a inductor on 9 of 9 designs, most often 1 µH. Counted from the KiCad layouts of 9 open source designs using the TPS61022.
What decoupling capacitors do designs use on the TPS61022 VOUT pin?
The VOUT pin has a decoupling capacitor on 9 of 9 designs, most often 22 µF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the TPS61022.
What resistor goes on the TPS61022 FB pin?
The FB pin has a resistor to GND on 9 of 9 designs, most often 100 kΩ (then 43 kΩ). Counted from the KiCad layouts of 9 open source designs using the TPS61022.
Which microcontrollers do boards using the TPS61022 use?
Most are built on ESP32 (3), AVR/Arduino (2), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the TPS61022?
The median is 54.7 × 62.6 mm, and 60% are two-layer designs.
What is the most popular open source board using the TPS61022?
By GitHub stars, Powerbank by k-off, with 4 stars.
Can I simulate one of these boards using the TPS61022 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.