14 open source boards using the OPA340NA
Real designs built with the OPA340NA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Otter-Iron
Jana-Marie
84 × 10 mm63 parts4LGPL-3.0520STM32
OtterIron Devkit
Jana-Marie
28 × 30 mm67 parts2LNo license321PIC
QI Charger
drewsum
150 × 50 mm293 parts2LNo license20STM32
UnMechanical
ebastler
214 × 145.5 mm156 parts4LCERN-OHL-P-2.013STM32
HeadphoneGuitarPracticeAmp
jbush001
80 × 30 mm51 parts4LApache-2.04STM32
OPS
Jana-Marie
49 × 34 mm98 parts2LNo license3Pyfive mpw1
PyFive-RISC-V
20.3 × 68.6 mm68 parts4LMIT3ESP32
Plant-Health-Meter
MarkusVLA
136.2 × 25 mm94 parts4LMIT2AVR/Arduino
Skin optoelectronics module
Roboy
20.6 × 6 mm77 parts4LNo license0AVR/Arduino
Audio shield
deniskokarev
52.1 × 54.6 mm11 parts2LNo license0- schematic only · 87 partsESP32
Crabsy
ZVV2
87 partsCERN-OHL-P-2.00 STM32
OtterIron PRO Bot
Jana-Marie
50 × 20.5 mm43 parts2LNo license321STM32
C6v1.0
parsa-novin
127 × 127 mm140 parts4LNo license2STM32
UEFI
Churrosoft
99 × 113 mm228 parts4LCERN-OHL-S-2.08
How designs wire the OPA340NA
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the OPA340NA connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 10 of 12 designs, most often 750 kΩ (then 2.37 kΩ).
- The V- pin is tied to GND on 12 of 12 designs.
- The - pin has a series resistor on 10 of 12 designs, most often 750 kΩ (then 100 kΩ).
- The V+ pin has a decoupling capacitor on 9 of 12 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| V-pin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: Signal 92% |
|
| -pin 4 | Connected to: Signal 100% |
|
| V+pin 5 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Otter-Iron by Jana-Marie, OtterIron Devkit by Jana-Marie, QI Charger by drewsum and UnMechanical by ebastler.
The OPA340NA in open source designs
The gallery holds 14 open source boards using the OPA340NA from 13 GitHub repositories; a typical one measures about 80 × 34 mm and carries around 82 components.
62% use four copper layers or more, and 50% carry an open source license.
The most starred is Otter-Iron by Jana-Marie.
Parts used alongside the OPA340NA
Microcontrollers on boards using the OPA340NA
What boards using the OPA340NA are built for
OPA340NA: common questions
Where can I find a OPA340NA reference design?
Each of the 14 boards on this page is a real design using the OPA340NA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA340NA pin 1?
Pin 1 has a series resistor on 10 of 12 designs, most often 750 kΩ (then 2.37 kΩ). Counted from the KiCad layouts of 12 open source designs using the OPA340NA.
How is the OPA340NA V- pin connected?
The V- pin is tied to GND on 12 of 12 designs. Counted from the KiCad layouts of 12 open source designs using the OPA340NA.
What resistor goes on the OPA340NA - pin?
The - pin has a series resistor on 10 of 12 designs, most often 750 kΩ (then 100 kΩ). Counted from the KiCad layouts of 12 open source designs using the OPA340NA.
What parts are used alongside the OPA340NA?
The AP2204R-3.3, MCP9700AT-ETT, SI8540, STUSB4500QTR and USBLC6-4SC6 appear in the most repositories here.
Which microcontrollers do boards using the OPA340NA use?
Most are built on STM32 (8), AVR/Arduino (2), ESP32 (2) and PIC (1).
How big is a typical board using the OPA340NA?
The median is 80 × 34 mm, and 38% are two-layer designs.
What is the most popular open source board using the OPA340NA?
By GitHub stars, Otter-Iron by Jana-Marie, with 520 stars.
Can I simulate one of these boards using the OPA340NA before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.