28 open source boards using the DRV8871DDA
Real designs built with the DRV8871DDA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
NOGGIN
berkeleyauv
31.3 × 34 mm57 parts4LGPL-3.03RP2040/RP2350
Midi controller
Tommie1236
100 × 100 mm515 parts4LCERN-OHL-W-2.02WildWillyR5Hardware
dkjonas
94.4 × 92.2 mm52 parts4LNo license1AVR/Arduino
Senior design
alaza252
50 × 60 mm24 parts2LNo license1ESP32
Atlas carrier ctrl
md-sazzad-eee
130 × 100 mm145 parts4LNo license0RP2040/RP2350
Spool
TheCacophonyProject
80 × 99 mm133 parts4LCERN-OHL-W-2.00ESP32
Kicad model train control
fanningert
212.3 × 91.7 mm99 parts2LNo license0RP2040/RP2350
Ir receiver
adeboni
100 × 100 mm84 parts2LNo license0RP2040/RP2350
Robot controller
mohan-bee
70 × 60 mm75 parts2LNo license0AVR/Arduino
MAIN
nolanconrad
94 × 120 mm72 parts2LNo license0ESP32
Voiture
KimotoHoitsu
110 × 103.3 mm70 parts2LNo license0ESP32
Battlebot
shobhitsinha04
101.6 × 76.2 mm69 parts2LNo license0ESP32
CDFR2026-PAMIs-2-DESIGN
robotronik
57 × 50 mm64 parts4LNo license0ESP32
CamRover
aravindjayan
88 × 60 mm62 parts2LNo license0STM32
Astrum
LtBrain
45.5 × 69.8 mm50 parts4LMIT0STM32
Wro26
Battlepillars
68.6 × 106.7 mm48 parts2LNo license0STM32
Aero
LtBrain
45.5 × 69.8 mm47 parts4LMIT0RP2040/RP2350
ESP32-ATT-C-LVGL8
oe5rnl
80 × 80 mm45 parts2LMIT0V-TRAD
Barkhausen-Institut
65 × 30 mm12 parts2LNo license0AVR/Arduino
Tenn
T3nk4I
86 × 25 mm30 parts2LGPL-2.027RP2040/RP2350
Faders
Tommie1236
160 × 130 mm348 parts2LCERN-OHL-W-2.02RP2040/RP2350
Ir transmitter
adeboni
114.3 × 25.4 mm81 parts2LNo license0AVR/Arduino
MainPCB REV 3
nolanconrad
70.2 × 67.8 mm66 parts2LNo license0AVR/Arduino
Logic
try-except
65.6 × 64.6 mm66 parts2LNo license0ESP32
Atlas agent ctrl
md-sazzad-eee
110 × 90 mm100 parts2LNo license0AVR/Arduino
CopyOfMain
nolanconrad
75 × 70.5 mm34 parts2LNo license0Drivers
try-except
53.6 × 60 mm30 parts4LNo license0AVR/Arduino
TRANSMITTER SMD
vul-os
39.4 × 54.3 mm12 parts2LMIT0
How designs wire the DRV8871DDA
Read from the KiCad layouts of 22 open source designs, one per repository: what each pin of the DRV8871DDA connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 19 of 21 designs, most often 30 kΩ (then 32 kΩ).
- The VM pin has a capacitor to GND on 17 of 21 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 7, 9 | Connected to: GND 94% | — |
| ILIMpin 4 | Connected to: Signal 95% |
|
| VMpin 5 | Connected to: DRV8871DDA 24% · BATT 48% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Tenn by T3nk4I, NOGGIN by berkeleyauv, Midi controller by Tommie1236 and Senior design by alaza252.
The DRV8871DDA in open source designs
The gallery holds 28 open source boards using the DRV8871DDA from 22 GitHub repositories; a typical one measures about 80 × 70.1 mm and carries around 65 components.
68% are two-layer designs, the rest use four layers or more, and 32% carry an open source license.
The most starred is Tenn by T3nk4I.
Parts used alongside the DRV8871DDA
Microcontrollers on boards using the DRV8871DDA
What boards using the DRV8871DDA are built for
DRV8871DDA: common questions
Where can I find a DRV8871DDA reference design?
Each of the 28 boards on this page is a real design using the DRV8871DDA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the DRV8871DDA ILIM pin?
The ILIM pin has a resistor to GND on 19 of 21 designs, most often 30 kΩ (then 32 kΩ). Counted from the KiCad layouts of 22 open source designs using the DRV8871DDA.
How is the DRV8871DDA VM pin connected?
The VM pin has a capacitor to GND on 17 of 21 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 22 open source designs using the DRV8871DDA.
What parts are used alongside the DRV8871DDA?
The RP2040, USBLC6-2SC6, AP2112K-3.3, ESP32-S3-WROOM-1 and L7805 appear in the most repositories here.
Which microcontrollers do boards using the DRV8871DDA use?
Most are built on AVR/Arduino (7), ESP32 (7), RP2040/RP2350 (7) and STM32 (4).
How big is a typical board using the DRV8871DDA?
The median is 80 × 70.1 mm, and 68% are two-layer designs.
What is the most popular open source board using the DRV8871DDA?
By GitHub stars, Tenn by T3nk4I, with 27 stars.
Can I simulate one of these boards using the DRV8871DDA before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.