DATN

nguyenmihn·IoT-LoRaGateway-and-IoT-LoRaNodes·gateway/DATN.kicad_pcb

DATN PCB layout, top view — open source ESP32 board by nguyenmihn

About the DATN PCB

DATN is an open source ESP32 PCB design by nguyenmihn, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 86.7 × 59.5 mm, with 110 components from 62 distinct parts.

Its main chip is the ESP32-WROOM-32UE, from the ESP32 family. Other key parts include the TPS62840DLCR, BQ24075RGT, MT3608, XL1509 and AI-THINKER-RA-02. By type, the board carries 39 capacitors, 34 resistors, 8 ICs, 6 transistors, 5 inductors and 4 connectors.

It belongs with the iot & wireless, sensors and rf & radio designs in this gallery.

From the project

Design and implementation of IoT-LoRaGateway and IoT-LoRaNodes applied in a building safety monitoring system (sponsored by ICE Meca Tech, Korea & IoTVision)

PSMS is an embedded IoT project integrating hardware design, firmware, and LoRa/TCP-IP communication to monitor and detect fire risks inside electrical panels.

- Goal: Detect early signs of sparks, smoke, and temperature anomalies in panels. - Use cases: Industrial installations like thermal power plants. - Communication: LoRa for remote, low-power detection; TCP-IP as wired fallback.

Main components on the DATN

DATN bill of materials (BOM)

110 components, 62 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TPS62840DLCR
U1
1
BQ24075RGT
U2
1
MT3608
U3
1
XL1509
U4
1
ESP32-WROOM-32UE
U5
1
AI-THINKER-RA-02
Ai-Thinker-Ra-02
U7
1
Ipex
U8
1
W5500
U12
3
SI2300
Q1, Q3, Q5
3
SI2301
Q2, Q4, Q6
1
Crystal_MCU
Y1
1
Jack-DC
J1
1
SCREW_TERMINAL_01X02
Screw_Terminal_01x02
J2
1
CONN_01X06_MALE
Conn_01x06_Male
J3
1
RJ45_HANRUN_HR911105A_HORIZONTAL
RJ45_Hanrun_HR911105A_Horizontal
J6
1
BATTERY_18650
Battery_18650
BT1
1
1A
F1
1
SOLDERJUMPER_2_OPEN
SolderJumper_2_Open
JP1
1
07D330K
RV1
1
100K
RV2
Show 42 more
QtyPartRefs
1
MSK-38/SS-12D00
SW1
1
SW_Push
SW2
1
SW_Push
SW3
1
3V3
Z1
1
12V
Z2
1
LED_Dual_AKAK
D1
2
SS34
D2, D3
1
FerriteBead
FB1
1
VHF160808H2N2ST
L1
1
22UH
22uH
L2
1
2.2UH
2.2uH
L3
1
47UH
47uH
L4
7
10UF
10uF
C1, C9, C10, C11, C12, C16, C18
5
100NF
100nF
C2, C13, C17, C19, C23
7
1UF
1uF
C3, C4, C6, C7, C8, C15, C21
1
220uF 35V
C5
1
110uF 10V
C14
2
18P
18p
C29, C30
1
0.1UF
0.1uF
C31
1
1NF/2KV
1nF/2kV
C33
1
22NF
22nF
C34
2
6.8NF
6.8nF
C35, C38
2
10NF
10nF
C39, C40
1
4.7UF
4.7uF
C41
6
0.1UF
0.1uF
C45, C46, C47, C48, C49, C50
2
10 uF 16V
C51, C52
4
1K
R1, R6, R13, R14
4
10K
R2, R12, R17, R18
1
12K
12k
R3
1
270K
R4
2
1K2
R5, R9
3
100K
R7, R11, R23
3
20K
R8, R15, R24
1
220K
R10
1
2K7
R16
1
1M
R36
5
0R
R37, R38, R45, R52, R53
2
330R
R46, R47
2
49R9
R48, R50
1
10R
R51
2
82R 1%
R54, R55
1
12.4K
12.4k
R56

DATN design files

The KiCad project lives in the nguyenmihn/IoT-LoRaGateway-and-IoT-LoRaNodes repository on GitHub; these links point at the commit this page was built from.

DATN: common questions

What microcontroller does the DATN use?

The DATN is built around the ESP32-WROOM-32UE, from the ESP32 family.

How big is the DATN PCB?

The DATN measures 86.7 × 59.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the DATN?

110 components, from 62 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the DATN design files?

From the nguyenmihn/IoT-LoRaGateway-and-IoT-LoRaNodes repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the DATN design in my own project?

Yes, under the terms of its Apache-2.0 license, which nguyenmihn chose for the repository.

Can I test firmware for the DATN without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in IoT-LoRaGateway-and-IoT-LoRaNodes

Similar boards