11 open source boards using the XL1509
Real designs built with the XL1509, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Tobor
evezor
263.5 × 63.5 mm122 parts2LCERN-OHL-P-2.0126ESP32
ESP32 Plotter Controller revB1
MarkJB
99.1 × 55.4 mm57 parts2LMIT9ESP32
Clean room slave
trieuhuyduc
165 × 110 mm207 parts2LNo license1ESP32
Hardware
nguyenmihn
116.2 × 69.6 mm163 parts2LApache-2.00RISC-V
EASYLINK
KrogeChen
87 × 72 mm118 parts2LNo license0ESP32
Mainboard
pumpingstationone
89.6 × 90 mm72 parts4LMIT0Sunrise alarm
nicollsf
95 × 60 mm48 parts2LNo license0Arm v3
evezor
250.2 × 63.3 mm100 parts4LCERN-OHL-P-2.0126ESP32
ESP32 Plotter Controller revB1 unrouted
MarkJB
99.1 × 55.4 mm49 parts2LMIT9ESP32
DATN
nguyenmihn
86.7 × 59.5 mm110 parts2LApache-2.00ESP32 Plotter Controller
MarkJB
99.1 × 55.4 mm34 parts2LMIT9
How designs wire the XL1509
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the XL1509 connects to, and the resistors, capacitors and other passives placed on it.
- The OUTPUT pin has a inductor on 7 of 7 designs, most often 68 µH (then 47 µH).
- The FEEDBACK pin is tied to 5V on 7 of 7 designs.
- The ON/OFF pin is tied to GND on 6 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: VIN 86% | — |
| OUTPUTpin 2 | Connected to: Signal 100% |
|
| FEEDBACKpin 3 | Connected to: 5V 100% | — |
| ON/OFFpin 4 | Connected to: GND 86% | — |
| GNDpin 5, 6, 7, 8 | Connected to: GND 86% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arm v3 by evezor, ESP32 Plotter Controller by MarkJB, Clean room slave by trieuhuyduc and EASYLINK by KrogeChen.
The XL1509 in open source designs
The gallery holds 11 open source boards using the XL1509 from 7 GitHub repositories; a typical one measures about 99.1 × 63.3 mm and carries around 100 components.
82% are two-layer designs, the rest use four layers or more, and 73% carry an open source license.
The most starred is Tobor by evezor.
Parts used alongside the XL1509
What boards using the XL1509 are built for
XL1509: common questions
Where can I find a XL1509 reference design?
Each of the 11 boards on this page is a real design using the XL1509. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the XL1509 OUTPUT pin connected?
The OUTPUT pin has a inductor on 7 of 7 designs, most often 68 µH (then 47 µH). Counted from the KiCad layouts of 7 open source designs using the XL1509.
How is the XL1509 FEEDBACK pin connected?
The FEEDBACK pin is tied to 5V on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the XL1509.
How is the XL1509 ON/OFF pin connected?
The ON/OFF pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the XL1509.
What parts are used alongside the XL1509?
The AMS1117-3.3, ESP32-WROOM-32U and Trans_CAN_SN65HVD230DR appear in the most repositories here.
Which microcontrollers do boards using the XL1509 use?
Most are built on ESP32 (7) and RISC-V (1).
How big is a typical board using the XL1509?
The median is 99.1 × 63.3 mm, and 82% are two-layer designs.
What is the most popular open source board using the XL1509?
By GitHub stars, Tobor by evezor, with 126 stars.
Can I simulate one of these boards using the XL1509 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.