ESP32-EVB Rev H

OLIMEX·ESP32-EVB·HARDWARE/REV-H/ESP32-EVB_Rev_H.kicad_pcb

ESP32-EVB Rev H PCB layout, top view — open source ESP32 board by OLIMEX

About the ESP32-EVB Rev H PCB

ESP32-EVB Rev H is an open source ESP32 PCB design by OLIMEX, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 75.2 × 74.7 mm, with 145 components from 68 distinct parts.

Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the TP4054-42-SOT25-R, SY8089AAAC(SOT23-5), LAN8710A-EZC(QFN32), CH340T(SSOP20W) and MCP2562-E/SN(SOIC-8_150mil). By type, the board carries 53 resistors, 30 capacitors, 10 ICs, 8 diodes, 6 transistors and 5 LEDs.

It belongs with the iot & wireless, power & battery and dev boards & breakouts designs in this gallery.

From the project

ESP32 WiFi / BLE Development board with Ethernet interface, Relays, microSD card

- revision A - internal, not released - revision B - initial public release - revision C - changes:

1. MicroUSB connector moved back, 40 mils to the middle of the board. 2. All mounting holes are now connected to GND. 3. Improved the ground layer around the infra red's pads and wires.

1. Changed R38 from 10k/0603 to 100k/0603 to lower the time without clock 2. Changed C28 from 100n/0603 to 10n/0603 to increase the time in reset

Main components on the ESP32-EVB Rev H

ESP32-EVB Rev H bill of materials (BOM)

145 components, 68 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TP4054-42-SOT25-R
BL4054B-42TPRN(SOT23-5)
U1
1
SY8089AAAC(SOT23-5)
U2
1
ESP32-WROOM-32E-N4
ESP32-WROOM-32D-4MB
U3
1
LAN8710A-EZC(QFN32)
U4
1
CH340T(SSOP20W)
U5
1
MCP2562-E/SN(SOIC-8_150mil)
U6
1
VS1838B
RPM7236-H8
U7
1
NCP303LSN27T1G(SOT-23-5)
U8
2
BAT54C(SOT23-3)
U9, U10
5
BC817-40(SOT23)
Q1, Q2, Q4, Q5, Q7
1
Q12MHZ/2P/20PPM/20PF/HU49SM
Q12MHz/20pF/30ppm/2P/HC-49SM(SMD)
Q3
2
DG306-5.0-3P
TB3 DG306-5.0-3P
CON1, CON2
1
Closed(1-2)/Opened(2-3)
5.0V/3.3V1
1
DW02R
BAT1
1
Opened(2-3)/Soldered(1-2)
BAT/BUT1
2
T1107A(6x3,8x2,5MM)
BUT1, RST1
1
TB3-3.5mm
CAN1
2
Opened
CAN_T1, PHY_RST1
1
Q50MHZ/25PPM/3V/4P/5X3.2MM
Q50MHz/25ppm/3V/4P/5x3.2mm
CR1
1
NA(HN2x20)
EXT1
Show 48 more
QtyPartRefs
3
WPM2015-3
WPM2015-3/TR
FET1, FET2, FET3
1
BSS138
FET4
2
MOUNTING_HOLE_SHIELD_3.3MM
Mounting_hole_Shield_3.3mm
MH2, MH3
1
TFC-WXCP11-08-LF
MICRO_SD1
1
PWRJ-2mm(YDJ-1134)
PWR1
1
NA(TB2 DG306-5.0-2P)
PWR2
2
RAS-0515
REL1, REL2
3
RA1206_(4X0603)_4B8_2.2k
RM1, RM2, RM3
1
BH10S
UEXT1
1
MISB-SWMM-5B-LF(USB_MICRO)
USB-UART1
1
LED/YELLOW/0603
LED/Yellow/0603
CHARGE1
2
LED/GREEN/0603
LED1, LED2
1
LED/IR333-A/5MM
LED/IR333-A/5mm
LED3
1
LED/RED/0603
PWRLED1
5
1N5819S4(SOD-123)
D1, D3, D5, D7, D8
1
SMBJ6.0A(DO-214AA)
D2
2
1N5822/SS34/SMA
D4, D6
3
600R/2A/UPZ2012E-601-2R0TF
FB0805/600R/2A
L1, L3, L4
1
2.2UH/NRS3015T2R2MNGH
2.2uH/1.5A/DCR=72mR/20%/3.00x3.00x1.50mm/CD32(NR3015T2R2M)
L2
1
NA(FB0805/600R/2A)
L5
2
NA(47uF/6.3V/20%/X5R/C0805)
C1, C3
3
47uF/6.3V/20%/X5R/C0805
C2, C4, C10
8
22uF/6.3V/20%/X5R/C0603
C5, C6, C7, C8, C9, C12, C23, C29
9
100nF/50V/20%/Y5V/C0603
C11, C13, C14, C15, C17, C24, C25, C27 +1
1
2.2uF/6.3V/10%/X5R/C0603
C16
1
NA(10uF/6.3V/20%/X5R/C0603)
C18
1
1nF/2000V/10%/X7R/C1206
C19
1
NA(1nF/2000V/10%/X7R/C1206)
C20
2
27pF/50V/5%/C0G/C0603
C21, C22
1
10uF/6.3V/20%/X5R/C0603
C26
1
470nF/16V/10%/X7R/C0603
C28
6
1K/R0603
1k/R0603
R1, R5, R41, R42, R50, R55
14
10K/R0603
10k/R0603
R2, R6, R22, R23, R29, R30, R34, R35 +6
6
2.2K/R0603
2.2k/R0603
R3, R4, R7, R11, R18, R21
1
2k/1%
R8
2
470K/R0603
470k/R0603
R9, R10
5
220R/R0603
R14, R16, R26, R27, R37
5
NA/R0603
R17, R44, R46, R48, R54
1
220K/R0603
220k/R0603
R19
1
49.9k/1%/R0603
R20
1
10K/R0603
470k/R0603
R24
1
0R(board_mounted)
R25
4
49.9R/1%/R0603
R28, R31, R32, R33
2
10R/R0603
R36, R43
1
12.1k/1%/R0603
R39
1
120R/R1206
R47
1
6.8R/R1206
R53
1
NA(1k/R0603)
R57

ESP32-EVB Rev H design files

The KiCad project lives in the OLIMEX/ESP32-EVB repository on GitHub; these links point at the commit this page was built from.

ESP32-EVB Rev H: common questions

What microcontroller does the ESP32-EVB Rev H use?

The ESP32-EVB Rev H is built around the ESP32-WROOM-32E-N4, from the ESP32 family.

How big is the ESP32-EVB Rev H PCB?

The ESP32-EVB Rev H measures 75.2 × 74.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ESP32-EVB Rev H?

145 components, from 68 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ESP32-EVB Rev H design files?

From the OLIMEX/ESP32-EVB repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the ESP32-EVB Rev H design in my own project?

Yes, under the terms of its Apache-2.0 license, which OLIMEX chose for the repository.

Can I test firmware for the ESP32-EVB Rev H without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ESP32-EVB

Similar boards