RadioCard
roblesterjr04·el-camino-dash·RadioCard/RadioCard.kicad_pcb
About the RadioCard PCB
RadioCard is an open source STM32 PCB design by roblesterjr04, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 60 mm, with 50 components from 33 distinct parts.
Its main chip is the STM32G0B1KBU6, from the STM32 family. Other key parts include the TJA1051T/3, AP2112K-3.3, Si4735-D60-GU and 74LVC1G125. By type, the board carries 16 capacitors, 16 resistors, 5 ICs, 5 connectors, 3 diodes and 2 jumpers.
It belongs with the rf & radio and audio designs in this gallery.
From the project
A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge and the antenna jack on the top edge (docs/hardware/accessoryports.md, rev 2 section). Any slot. Spec: docs/hardware/radiocard.md. On it: - a Si4735-D6
A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge and the antenna jack on the top edge (docs/hardware/accessoryports.md, rev 2 section). Any slot. Spec: docs/hardware/radiocard.md. On it: - a Si4735-D60-GU AM/FM/SW/LW tuner with RDS (SSOP-24), controlled over I2C, its digital audio a slave on the slot I2S rail's clocks, its reference clock taken from the rail's BCK (no oscillator) - an STM32G0B1KBU6 (FDCAN) with an 8 MHz oscillator into PC14 (HSE bypass), an MCP2562 CAN transceiver and an AP2112K-3.3 from the…
Main components on the RadioCard
RadioCard bill of materials (BOM)
50 components, 33 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G0B1KBU6 | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U1 |
| 1 | TJA1051T/3 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | Si4735-D60-GU | SSOP-24_3.9x8.7mm_P0.635mm | U4 |
| 1 | 74LVC1G125 | SOT-353_SC-70-5 | U5 |
| 1 | 8MHz | Oscillator_SMD_Abracon_ASE-4Pin_3.2x2.5mm | Y1 |
| 1 | DigiDash slot | PinHeader_2x15_P2.54mm_Horizontal | J1 |
| 1 | Antenna (SMA) | SMA_Amphenol_132289_EdgeMount | J2 |
| 1 | SWD | PinHeader_1x05_P2.54mm_Horizontal | J3 |
| 1 | Debug serial | PinHeader_1x03_P2.54mm_Horizontal | J4 |
| 1 | AM loopstick | PinHeader_1x02_P2.54mm_Horizontal | J5 |
| 1 | Tuner address | SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1 |
| 1 | AM from whip | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | TUNED | LED_0603_1608Metric | D1 |
| 1 | TPD1E0B04 | D_0402_1005Metric | D2 |
| 1 | STEREO/RDS | LED_0603_1608Metric | D3 |
| 1 | BLM18 120R | L_0603_1608Metric | FB1 |
| 1 | 56nH | L_0603_1608Metric | L1 |
| 3 | 10u | C_0805_2012Metric | C1, C2, C4 |
| 8 | 100n | C_0603_1608Metric | C3, C5, C7, C9, C10, C11, C13, C15 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4.7u | C_0603_1608Metric | C6 |
| 1 | 22n | C_0603_1608Metric | C12 |
| 1 | 2.2p | C_0603_1608Metric | C14 |
| 1 | 1n | C_0603_1608Metric | C16 |
| 1 | 470n | C_0603_1608Metric | C17 |
| 2 | 10k | R_0603_1608Metric | R1, R15 |
| 3 | 1k | R_0603_1608Metric | R2, R3, R4 |
| 1 | 604 | R_0603_1608Metric | R5 |
| 2 | 2k | R_0603_1608Metric | R6, R7 |
| 4 | 100k | R_0603_1608Metric | R8, R9, R12, R14 |
| 2 | 4.7k | R_0603_1608Metric | R10, R11 |
| 1 | 0 | R_0603_1608Metric | R13 |
| 1 | 33 | R_0603_1608Metric | R16 |
RadioCard design files
The KiCad project lives in the roblesterjr04/el-camino-dash repository on GitHub; these links point at the commit this page was built from.
RadioCard: common questions
What microcontroller does the RadioCard use?
The RadioCard is built around the STM32G0B1KBU6, from the STM32 family.
How big is the RadioCard PCB?
The RadioCard measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RadioCard?
50 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RadioCard design files?
From the roblesterjr04/el-camino-dash repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RadioCard design in my own project?
Yes, under the terms of its MIT license, which roblesterjr04 chose for the repository.
Can I test firmware for the RadioCard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in el-camino-dash
ESP32
Panel
roblesterjr04
329 × 255.5 mm483 parts4LMIT6DigiDash2
roblesterjr04
329 × 113 mm179 parts4LMIT6DigiDash3
roblesterjr04
329 × 113 mm150 parts2LMIT6STM32
SensorCard2
roblesterjr04
80 × 60 mm114 parts2LMIT6AVR/Arduino
SensorCard
roblesterjr04
80 × 60 mm114 parts4LMIT6AVR/Arduino
DigiDash
roblesterjr04
309 × 103.5 mm97 parts2LMIT6ESP32
AudioCarrier
roblesterjr04
80 × 60 mm77 parts2LMIT6BenchBoard
roblesterjr04
100 × 100 mm67 parts2LMIT6ESP32
ConsoleBoard
roblesterjr04
100 × 50 mm60 parts4LMIT6ESP32
LTECard
roblesterjr04
80 × 60 mm58 parts4LMIT6ESP32
ConsoleBoardRS
roblesterjr04
108 × 35 mm42 parts2LMIT6
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k