LTECard
roblesterjr04·el-camino-dash·LTECard/LTECard.kicad_pcb
About the LTECard PCB
LTECard is an open source ESP32 PCB design by roblesterjr04, published on GitHub under the MIT license. It is a 4-layer board measuring 80 × 60 mm, with 58 components from 39 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the MCP2562-E/SN, AP7361C-33E, USBLC6-2SC6 and TPS54560BDDA. By type, the board carries 21 resistors, 20 capacitors, 5 ICs, 5 connectors, 4 diodes and 2 switches.
It belongs with the rf & radio designs in this gallery.
From the project
A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge (docs/hardware/accessoryports.md, rev 2 section). Spec: docs/hardware/ltecard.md. It goes in any slot. On it: - an ESP32-S3-WROOM-1-N16R8 module (16 MB
A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge (docs/hardware/accessoryports.md, rev 2 section). Spec: docs/hardware/ltecard.md. It goes in any slot. On it: - an ESP32-S3-WROOM-1-N16R8 module (16 MB flash, 8 MB octal PSRAM), antenna at the top-left corner - a SIMCom A7670 LTE Cat-1 core board (a ready-made breakout) on two female sockets, 1 × 12 and 1 × 11, 8.5 mm tall - a TPS54560B buck making the core board's 5 V from AUX 12 V (slot pins 25–30), with 470 µF bulk at its VIN - an MCP2562 CAN transceiver and an…
Main components on the LTECard
LTECard bill of materials (BOM)
58 components, 39 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | MCP2562-E/SN | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | AP7361C-33E | SOT-223-3_TabPin2 | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | TPS54560BDDA | TI_SO-PowerPAD-8_ThermalVias | U5 |
| 1 | DigiDash slot | PinHeader_2x15_P2.54mm_Horizontal | J1 |
| 1 | LTE core row A | PinSocket_1x12_P2.54mm_Vertical | J2 |
| 1 | LTE core row B | PinSocket_1x11_P2.54mm_Vertical | J3 |
| 1 | USB-C | USB_C_Receptacle_Amphenol_12401948E412A | J4 |
| 1 | Debug serial | PinHeader_1x03_P2.54mm_Horizontal | J5 |
| 1 | RESET | SW_SPST_PTS810 | SW1 |
| 1 | BOOT | SW_SPST_PTS810 | SW2 |
| 1 | LTE green | LED_0603_1608Metric | D1 |
| 1 | Wi-Fi blue | LED_0603_1608Metric | D2 |
| 1 | B360B | D_SMB | D3 |
| 1 | BZT52C5V1 | D_SOD-123 | D4 |
| 1 | 6.8u | L_Bourns_SRP7028A_7.3x6.6mm | L1 |
| 1 | 10u | C_0805_2012Metric | C1 |
| 2 | 22u | C_0805_2012Metric | C2, C3 |
| 6 | 100n | C_0603_1608Metric | C4, C6, C7, C12, C19, C20 |
Show 19 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1u | C_0603_1608Metric | C5 |
| 3 | 2.2u 100V | C_1210_3225Metric | C8, C9, C10 |
| 1 | 100n | C_0805_2012Metric | C11 |
| 3 | 47u 10V | C_1210_3225Metric | C13, C14, C15 |
| 1 | 4.7n | C_0603_1608Metric | C16 |
| 1 | 47p | C_0603_1608Metric | C17 |
| 1 | 470u 10V | CP_Elec_8x10 | C18 |
| 3 | 10k | R_0603_1608Metric | R1, R2, R3 |
| 2 | 5.1k | R_0603_1608Metric | R4, R5 |
| 7 | 1k | R_0603_1608Metric | R6, R7, R8, R15, R17, R18, R19 |
| 1 | 243k | R_0603_1608Metric | R9 |
| 1 | 442k | R_0603_1608Metric | R10 |
| 1 | 90.9k | R_0603_1608Metric | R11 |
| 1 | 53.6k | R_0603_1608Metric | R12 |
| 1 | 10.2k | R_0603_1608Metric | R13 |
| 1 | 16.9k | R_0603_1608Metric | R14 |
| 1 | 100k | R_0603_1608Metric | R16 |
| 1 | 22k | R_0603_1608Metric | R20 |
| 1 | 33k | R_0603_1608Metric | R21 |
LTECard design files
The KiCad project lives in the roblesterjr04/el-camino-dash repository on GitHub; these links point at the commit this page was built from.
LTECard: common questions
What microcontroller does the LTECard use?
The LTECard is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the LTECard PCB?
The LTECard measures 80 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the LTECard?
58 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LTECard design files?
From the roblesterjr04/el-camino-dash repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LTECard design in my own project?
Yes, under the terms of its MIT license, which roblesterjr04 chose for the repository.
Can I test firmware for the LTECard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in el-camino-dash
ESP32
Panel
roblesterjr04
329 × 255.5 mm483 parts4LMIT6DigiDash2
roblesterjr04
329 × 113 mm179 parts4LMIT6DigiDash3
roblesterjr04
329 × 113 mm150 parts2LMIT6STM32
SensorCard2
roblesterjr04
80 × 60 mm114 parts2LMIT6AVR/Arduino
SensorCard
roblesterjr04
80 × 60 mm114 parts4LMIT6AVR/Arduino
DigiDash
roblesterjr04
309 × 103.5 mm97 parts2LMIT6ESP32
AudioCarrier
roblesterjr04
80 × 60 mm77 parts2LMIT6BenchBoard
roblesterjr04
100 × 100 mm67 parts2LMIT6ESP32
ConsoleBoard
roblesterjr04
100 × 50 mm60 parts4LMIT6STM32
RadioCard
roblesterjr04
80 × 60 mm50 parts2LMIT6ESP32
ConsoleBoardRS
roblesterjr04
108 × 35 mm42 parts2LMIT6
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k