SensorCard

roblesterjr04·el-camino-dash·SensorCard/SensorCard.kicad_pcb

SensorCard PCB layout, top view — open source AVR/Arduino board by roblesterjr04

About the SensorCard PCB

SensorCard is an open source AVR/Arduino PCB design by roblesterjr04, published on GitHub under the MIT license. It is a 4-layer board measuring 80 × 60 mm, with 114 components from 56 distinct parts.

Its main chip is the ATmega2560-16AU, from the AVR/Arduino family. Other key parts include the MCP2515-I/SO, TJA1051T/3, MB85RC256V and PC817. By type, the board carries 44 resistors, 27 capacitors, 16 jumpers, 10 connectors, 6 diodes and 5 ICs.

It belongs with the audio and rf & radio designs in this gallery.

From the project

The dash's sensor pack on a slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge (docs/hardware/accessoryports.md`, rev 2 section). It reads the senders, the speed sensor, the tach, ignition, battery and th

The dash's sensor pack on a slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge (docs/hardware/accessoryports.md`, rev 2 section). It reads the senders, the speed sensor, the tach, ignition, battery and the alternator lamp terminal, keeps the odometer in FRAM, and sends the gauges' frames on CAN. It used to be part of the main board; it moved to a card so that a change to the sender, speed or tach wiring means a new card, not a new main board.

Main components on the SensorCard

SensorCard bill of materials (BOM)

114 components, 56 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATmega2560-16AU
U1
1
MCP2515-I/SO
U2
1
TJA1051T/3
U3
1
MB85RC256V
U4
1
PC817
U5
2
16MHz
Y1, Y2
1
DigiDash slot
J1
1
Senders
J2
1
Speed
J3
1
Tach
J4
1
RPM select
J5
1
AVR-ISP-6
J6
1
FTDI
J7
1
Sensor serial out
J8
1
Demo
J9
1
Spare I/O
J10
3
PTC 0.1A
F1, F2, F3
1
5V / 12V
JP1
1
FUEL PU / PD
JP2
1
ETEMP PU / PD
JP3
Show 36 more
QtyPartRefs
1
OILP PU / PD
JP4
1
AMB PU / PD
JP5
1
FUEL 100
JP6
1
FUEL 220
JP7
1
FUEL 470
JP8
1
ETEMP 220
JP9
1
ETEMP 1k
JP10
1
ETEMP 10k
JP11
1
OILP 220
JP12
1
OILP 1k
JP13
1
OILP 100k
JP14
1
AMB 10k
JP15
1
AMB 100k
JP16
3
BAT54S
D1, D4, D5
1
BAT42W
D2
1
green
D3
1
1N4148W
D6
1
600R
FB1
2
10u
C1, C9
14
100n
C2, C3, C4, C5, C6, C7, C8, C10 +6
4
18p
C12, C13, C16, C17
4
10n
C20, C21, C22, C23
1
100n
C25
2
1n
C26, C27
1
15k
R1
18
10k
R2, R6, R8, R10, R11, R12, R17, R19 +10
3
100k
R3, R30, R32
3
22k
R4, R37, R43
3
4.7k
R5, R13, R14
1
47k
R7
7
1k
R9, R16, R18, R20, R26, R29, R44
1
100
R15
1
100
R22
3
220
R23, R25, R28
1
470
R24
2
4.7k
R41, R42

SensorCard design files

The KiCad project lives in the roblesterjr04/el-camino-dash repository on GitHub; these links point at the commit this page was built from.

SensorCard: common questions

What microcontroller does the SensorCard use?

The SensorCard is built around the ATmega2560-16AU, from the AVR/Arduino family.

How big is the SensorCard PCB?

The SensorCard measures 80 × 60 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the SensorCard?

114 components, from 56 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SensorCard design files?

From the roblesterjr04/el-camino-dash repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the SensorCard design in my own project?

Yes, under the terms of its MIT license, which roblesterjr04 chose for the repository.

Can I test firmware for the SensorCard without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in el-camino-dash

Similar boards