AudioCarrier

roblesterjr04·el-camino-dash·AudioCarrier/AudioCarrier.kicad_pcb

AudioCarrier PCB layout, top view — open source ESP32 board by roblesterjr04

About the AudioCarrier PCB

AudioCarrier is an open source ESP32 PCB design by roblesterjr04, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 60 mm, with 77 components from 26 distinct parts.

Its main chip is the ESP32-DevKitC-VE, from the ESP32 family. Other key parts include the TJA1051T/3, TLV9062AIDGK, PCM1808PW, PCM5102APW and 74LVC125APW. By type, the board carries 40 capacitors, 25 resistors, 7 ICs, 3 connectors and 2 inductors.

It belongs with the audio designs in this gallery.

From the project

A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge and its jacks on the top edge (docs/hardware/accessoryports.md, rev 2 section). It goes in slot 1: the RCA block is 26.5 mm tall, and slot 1 is the one

A slot card for the DigiDash rev 2 board: 80 × 60 mm, standing on edge in a 2×15 slot, its right-angle header on the bottom edge and its jacks on the top edge (docs/hardware/accessoryports.md, rev 2 section). It goes in slot 1: the RCA block is 26.5 mm tall, and slot 1 is the one whose parts side faces off the end of the row. It is the clock master of the slot's I2S rail, which reaches every other slot (an AI voice card can go in any of them). The directory keeps its old name. On it: - an ESP32-DevKitC-VE (the bench board: ESP32-WROVER-E, classic ESP32 for A2DP + AVRCP + HFP; 8 MB flash, 8 MB…

Main components on the AudioCarrier

AudioCarrier bill of materials (BOM)

77 components, 26 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-DevKitC-VE
U1
1
TJA1051T/3
U2
1
TLV9062AIDGK
U3
1
PCM1808PW
U4
2
PCM5102APW
U5, U6
1
74LVC125APW
U8
1
DigiDash slot
J1
1
RCA block
J2
1
Mic in
J6
2
600R @100MHz
FB1, FB2
9
10u
C2, C5, C7, C16, C25, C34, C36, C41 +1
17
100n
C4, C6, C11, C12, C15, C17, C18, C19 +9
4
2.2u
C13, C14, C22, C23
4
2.2n
C20, C21, C29, C30
1
47u
C31
2
100p
C32, C35
3
1u
C33, C37, C38
4
10k
R1, R13, R14, R22
2
1k
R4, R10
4
470
R5, R6, R7, R8
Show 6 more
QtyPartRefs
3
100k
R9, R12, R24
2
2.2k
R11, R16
1
47k
R15
6
33
R17, R18, R19, R20, R21, R23
2
100
R25, R26
1
10
R27

AudioCarrier design files

The KiCad project lives in the roblesterjr04/el-camino-dash repository on GitHub; these links point at the commit this page was built from.

AudioCarrier: common questions

What microcontroller does the AudioCarrier use?

The AudioCarrier is built around the ESP32-DevKitC-VE, from the ESP32 family.

How big is the AudioCarrier PCB?

The AudioCarrier measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the AudioCarrier?

77 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the AudioCarrier design files?

From the roblesterjr04/el-camino-dash repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the AudioCarrier design in my own project?

Yes, under the terms of its MIT license, which roblesterjr04 chose for the repository.

Can I test firmware for the AudioCarrier without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in el-camino-dash

Similar boards