Placed

sequoia-hope·circuit-composer·boards/easy2350/floorplan/placed.kicad_pcb

Placed PCB layout, top view — open source RP2040/RP2350 board by sequoia-hope

About the Placed PCB

Placed is an open source RP2040/RP2350 PCB design by sequoia-hope, published on GitHub under the MIT license. It is a 2-layer board measuring 21.1 × 51.1 mm, with 57 components from 31 distinct parts.

Its main chip is the RP2350_60QFN, from the RP2040/RP2350 family. Other key parts include the USBLC6-2SC6, AP7361C-33FGE, SN74LV1T125DBVR and W25Q128JVS. By type, the board carries 25 capacitors, 12 resistors, 7 diodes, 5 ICs, 4 connectors and 2 switches.

It belongs with the power & battery designs in this gallery.

From the project

Board design as composition: verified chip packages, intent files and generated critical blocks for KiCad, between easy_pcb and ultraroute

Board design as composition: chips are ingested once into verified, published packages, and boards are built by combining them. It covers the stage between schematic and routing: constraint definition and physical design planning. The full design is in Circuit Composer — System Spec.md.

- easypcb runs a board from requirements to fab outputs with the pcb-design skill. Its phase-3 classification (design/nets.csv) imports into an intent file, and its worked example, easy2350, is the first annotated board here. - ultraroute** is the router. It takes this project's output: a KiCad board with…

Main components on the Placed

Placed bill of materials (BOM)

57 components, 31 distinct parts.

QtyPartRefs
1
RP2350_60QFN
U1
1
USBLC6-2SC6
U2
1
AP7361C-33FGE
U3
1
SN74LV1T125DBVR
U4
1
W25Q128JVS
U5
1
ABM8-272-T3
Y1
1
USB-C
J1
1
GPIO left
J2
1
GPIO right
J3
1
SWD
J4
1
SW_Push
SW1
1
RESET
SW2
1
RED
D1
1
SM4007PL
D2
4
WS2812B-2020-V6
D3, D4, D5, D6
1
BZT52B5V1
D7
1
3.3u
L1
16
100n
C1, C4, C5, C6, C7, C8, C9, C11 +8
1
2.2u
C2
1
10u
C3
Show 11 more
QtyPartRefs
2
4.7u
C13, C16
2
4.7u
C14, C15
2
15p
C20, C21
1
4.7u
C23
2
5.1k
R1, R2
1
33
R3
2
27
R4, R5
4
1k
R6, R7, R8, R9
1
33R
R10
1
4.7k
R11
1
100k
R12

Placed design files

The KiCad project lives in the sequoia-hope/circuit-composer repository on GitHub; these links point at the commit this page was built from.

Placed: common questions

What microcontroller does the Placed use?

The Placed is built around the RP2350_60QFN, from the RP2040/RP2350 family.

How big is the Placed PCB?

The Placed measures 21.1 × 51.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Placed?

57 components, from 31 distinct parts. The full bill of materials is listed on this page.

Where can I download the Placed design files?

From the sequoia-hope/circuit-composer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Placed design in my own project?

Yes, under the terms of its MIT license, which sequoia-hope chose for the repository.

Can I test firmware for the Placed without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in circuit-composer

Similar boards