ESP32-C3-pre
syamei0·Y.maku·kicad/ESP32-C3-pre/ESP32-C3-pre.kicad_pcb
About the ESP32-C3-pre PCB
ESP32-C3-pre is an open source ESP32 PCB design by syamei0, published on GitHub. It is a 2-layer board measuring 72 × 95 mm, with 9 components from 6 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the LM1117DT-3.3. By type, the board carries 2 ICs, 2 switches, 2 capacitors, 2 resistors and 1 connector.
It belongs with the iot & wireless designs in this gallery.
From the project
左側はおまけのam2837モタドラ ### 仕様 - wifi - Bluetooth - RJ45-CAN - type-c書き込み ### ⚠注意⚠ - RJ45-書き込み非対応
Main components on the ESP32-C3-pre
ESP32-C3-pre bill of materials (BOM)
9 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | LM1117DT-3.3 LM1117GS-3.3 | SOT-223 | U2 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 2 | SW_Push | SW_PUSH_1P1T_6x3.5mm_H5.0_APEM_MJTP1250 | SW1, SW2 |
| 2 | 0.1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | 5.1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
ESP32-C3-pre design files
The KiCad project lives in the syamei0/Y.maku repository on GitHub; these links point at the commit this page was built from.
ESP32-C3-pre: common questions
What microcontroller does the ESP32-C3-pre use?
The ESP32-C3-pre is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the ESP32-C3-pre PCB?
The ESP32-C3-pre measures 72 × 95 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-C3-pre?
9 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32-C3-pre design files?
From the syamei0/Y.maku repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32-C3-pre design in my own project?
The repository has no license, so all rights stay with syamei0. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32-C3-pre without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Y.maku
ESP32
ESP32-S3
syamei0
95 × 72 mm142 parts2LNo license0ESP32
Syamei0 MD
syamei0
3.2 × 3.2 mm132 parts2LNo license0ESP32
ESP32 SMD
syamei0
95 × 72 mm113 parts2LNo license0RP2040/RP2350
RP2040 Minimal Design Example
syamei0
72 × 95 mm68 parts2LNo license0ESP32
ESP32C3-miniMAS
syamei0
97 × 72 mm57 parts2LNo license0ESP32
STM32
syamei0
100 × 100 mm33 parts2LNo license0Power supply
syamei0
95 × 72 mm31 parts2LNo license0ESP32
ESP32
syamei0
100 × 100 mm23 parts2LNo license0ESP32-S3-Evaluation Board
syamei0
40 × 64 mm20 parts2LNo license0ESP32-C3-Evaluation Board
syamei0
40 × 64 mm20 parts2LNo license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k