Bonk
tyke01·bonk
About the Bonk PCB
Bonk is an open source ESP32 PCB design by tyke01, published on GitHub. It is a 4-layer board measuring 125 × 100 mm, with 72 components from 38 distinct parts.
Its main chip is the ESP32-SL, from the ESP32 family. Other key parts include the CR2013-MI2120, AP2112K-3.3, INA226, COM-09032 and TP4056-42-ESOP8. By type, the board carries 26 resistors, 17 capacitors, 10 ICs, 5 switches, 5 diodes and 4 transistors.
It belongs with the iot & wireless, power & battery and rf & radio designs in this gallery.
From the project
An open source RC controller.
An open-source handheld RC transmitter built around the ESP32. Designed by Spectral Systems.
- Features - Repository layout - Hardware overview - Power architecture - ESP32 pin map - Buses and addresses - Firmware notes - Bill of materials - Manufacturing - Assembly - Bring-up checklist - Known issues (Rev 1) - License
- MCU: ESP32 module (Ai-Thinker ESP32-SL) with on-board PCB antenna - Inputs: 2 analog joysticks, 2 potentiometers, 2 toggle switches, a rotary encoder with push switch, and BOOT/EN buttons - Display: 2.8" ILI9341 320x240 SPI TFT module (its SD card slot is not used) - Radio…
Main components on the Bonk
Bonk bill of materials (BOM)
72 components, 38 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CR2013-MI2120 | CR2013-MI2120 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | INA226 | TSSOP-10_3x3mm_P0.5mm | U3 |
| 2 | COM-09032 | XDCR_COM-09032 | U4, U5 |
| 1 | TP4056-42-ESOP8 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U6 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U7 |
| 1 | CP2102N-AXX-XQFN24 CP2102N-Axx-xQFN24 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U8 |
| 1 | DW01A | SOT-23-6 | U9 |
| 1 | NRF24L01_BREAKOUT NRF24L01_Breakout | nRF24L01_Breakout | U10 |
| 2 | BC817 | SOT-23 | Q1, Q2 |
| 1 | AO3401A | SOT-23 | Q3 |
| 1 | FS8205A | SOP65P640X120-8N | Q4 |
| 1 | USB4085-GF-A | USB4085_CONNECTOR | X1 |
| 1 | 1048 | Battery_Holder_18650_2_Cell_SMD | BT1 |
| 2 | R_Potentiometer | Potentiometer_Vishay_T93YA_Vertical | RV1, RV2 |
| 1 | PEC12R-4217F-S0024 | XDCR_PEC12R-4217F-S0024 | S1 |
| 2 | 472123010111 | toggle_switch | S2, S3 |
| 2 | SW_Push | SW_PUSH_6mm_H7.3mm | SW3, SW4 |
| 4 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D4, D5 |
| 1 | SS34 | D_SMA | D3 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-SL Ai-Thinker(安信可) | WIFIM-SMD_ESP32-SL | L1 |
| 2 | 10NF 10nf | C_0603_1608Metric | C1, C2 |
| 7 | 0.1U 0.1u | C_0603_1608Metric | C3, C5, C7, C9, C10, C14, C17 |
| 5 | 10U 10u | C_0603_1608Metric | C4, C6, C8, C15, C16 |
| 1 | 4.7U 4.7u | C_0603_1608Metric | C11 |
| 2 | 1u | C_0603_1608Metric | C12, C13 |
| 8 | 10K | R_0603_1608Metric | R2, R3, R4, R5, R18, R19, R20, R21 |
| 2 | 50 | R_0603_1608Metric | R6, R7 |
| 2 | 470 | R_0603_1608Metric | R8, R12 |
| 2 | 4K7 4k7 | R_0603_1608Metric | R9, R10 |
| 1 | 20M 20m | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R11 |
| 4 | 1k | R_0603_1608Metric | R13, R22, R23, R26 |
| 1 | 47K5 47k5 | R_0603_1608Metric | R14 |
| 1 | 22K1 22k1 | R_0603_1608Metric | R15 |
| 2 | 5K1 5k1 | R_0603_1608Metric | R16, R17 |
| 1 | 1K1 1k1 | R_0603_1608Metric | R24 |
| 1 | 100 | R_0603_1608Metric | R25 |
| 1 | 100K 100k | R_0603_1608Metric | R27 |
Bonk design files
The KiCad project lives in the tyke01/bonk repository on GitHub; these links point at the commit this page was built from.
- LayoutRC controller.kicad_pcb
- SchematicRC controller.kicad_sch
- BOMbom/RC controller.csv
Bonk: common questions
What microcontroller does the Bonk use?
The Bonk is built around the ESP32-SL, from the ESP32 family.
How big is the Bonk PCB?
The Bonk measures 125 × 100 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Bonk?
72 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bonk design files?
From the tyke01/bonk repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Bonk design in my own project?
The repository has no license, so all rights stay with tyke01. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Bonk without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k