Camera interface CAN board

waterloo-rocketry·canhw·camera_interface_CAN_board/camera_interface_CAN_board.kicad_pcb

Camera interface CAN board layout, top view — open source PIC board by waterloo-rocketry

About the Camera interface CAN board

Camera interface CAN board is an open source PIC PCB design by waterloo-rocketry, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 38.6 × 29 mm, with 44 components from 29 distinct parts.

Its main chip is the canhw:PIC18F26K83, from the PIC family. Other key parts include the canhw:MCP2562, TPS259472ARPW, INA180A3 and TPS22958NDGKR. By type, the board carries 16 capacitors, 14 resistors, 5 ICs, 4 connectors, 4 diodes and 1 crystal.

It belongs with the rf & radio designs in this gallery.

From the project

Hardware monorepo avionics PCB

This repository tracks the hardware development for the RocketCAN project. All schematics, board designs, and fabrication files are tracked in this repository. The corresponding software running on each board can be found in the cansw repositories. The CAN driver library used is tracked in the canlib repository.

All hardware files were developed in KiCAD.

The RocketCAN project is an extension of the 2018 Flight Instrumentation project. The functions of the original Flight Instrumentation electronics are decoupled into several single-function modules connected by a Controller Area Network…

Main components on the Camera interface CAN board

canhw:PIC18F26K83canhw:MCP2562TPS259472ARPWINA180A3TPS22958NDGKR

Camera interface CAN board bill of materials (BOM)

44 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
canhw:PIC18F26K83
U1
1
canhw:MCP2562
U2
1
TPS259472ARPW
U3
1
INA180A3
U4
1
TPS22958NDGKR
U5
1
ABM8G-12.000MHZ-18-D2Y-T
Y1
1
Programming Header
J1
1
G125-MH104M4-04AD000P
J2
1
Analog_Video
J3
1
G125-MG10605M4P
J4
1
WHITE
D1
1
RED
D2
1
BLUE
D3
1
SMF13CA
D4
2
27PF
27pF
C1, C2
5
0.1UF
0.1uF
C3, C4, C5, C9, C10
3
1UF
1uF
C6, C11, C16
1
10NF
10nF
C7
3
10UF
10uF
C8, C13, C14
2
2.2NF
2.2nF
C12, C15
Show 9 more
QtyPartRefs
4
330R
R1, R2, R3, R8
2
10K
R4, R9
1
390K
390k
R5
1
3.3K
3.3k
R6
1
40MR
40mR
R7
1
120R
R10
1
0R
R11
2
2k
R12, R14
1
1k
R13

Camera interface CAN board design files

The KiCad project lives in the waterloo-rocketry/canhw repository on GitHub; these links point at the commit this page was built from.

Camera interface CAN board: common questions

What microcontroller does the Camera interface CAN board use?

The Camera interface CAN board is built around the canhw:PIC18F26K83, from the PIC family.

How big is the Camera interface CAN board?

The Camera interface CAN board measures 38.6 × 29 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Camera interface CAN board?

44 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Camera interface CAN board design files?

From the waterloo-rocketry/canhw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Camera interface CAN board design in my own project?

Yes, under the terms of its GPL-3.0 license, which waterloo-rocketry chose for the repository.

Can I test firmware for the Camera interface CAN board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in canhw

Similar boards