Injector sensor hub
waterloo-rocketry·canhw·injector_sensor_hub/injector_sensor_hub.kicad_pcb
About the Injector sensor hub PCB
Injector sensor hub is an open source PIC PCB design by waterloo-rocketry, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 58.4 × 45.7 mm, with 58 components from 25 distinct parts.
Its main chip is the PIC18F26K83, from the PIC family. Other key parts include the MCP2562 and INA180. By type, the board carries 22 resistors, 10 connectors, 6 capacitors, 4 ICs, 3 diodes and 2 fuses.
It belongs with the rf & radio and sensors designs in this gallery.
From the project
Hardware monorepo avionics PCB
This repository tracks the hardware development for the RocketCAN project. All schematics, board designs, and fabrication files are tracked in this repository. The corresponding software running on each board can be found in the cansw repositories. The CAN driver library used is tracked in the canlib repository.
All hardware files were developed in KiCAD.
The RocketCAN project is an extension of the 2018 Flight Instrumentation project. The functions of the original Flight Instrumentation electronics are decoupled into several single-function modules connected by a Controller Area Network…
Main components on the Injector sensor hub
Injector sensor hub bill of materials (BOM)
58 components, 25 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP2562 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | PIC18F26K83 | SOIC-28W_7.5x17.9mm_P1.27mm | U2 |
| 2 | INA180 | SOT-23-5_HandSoldering | U3, U4 |
| 1 | Crystal | Crystal_HC49-4H_Vertical | Y1 |
| 1 | CAN_Connector | connector_Harwin_G125–MG10605M4P | J1 |
| 1 | Programming Header | PinSocket_5x2.54_SMD_90deg_952-3198-1-ND | J2 |
| 5 | CONN_01X02_FEMALE-CONNECTOR Conn_01x02_Female-Connector | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J3, J4, J6, J8, J10 |
| 3 | CONN_01X03_FEMALE Conn_01x03_Female | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J5, J7, J9 |
| 8 | TestPoint | TestPoint_Keystone_5005-5009_Compact | 2A1, 2A2, 2A3, 2A4, 2A5, 3A1, 3A2, 3A3 |
| 2 | 350MA 350mA | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1, F2 |
| 1 | TP_5V | TestPoint_Keystone_5005-5009_Compact | TP1 |
| 1 | TP_12V | TestPoint_Keystone_5005-5009_Compact | TP4 |
| 1 | BLUE | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | WHITE | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | RED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3 |
| 1 | 10UF 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 2 | 0.1UF 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 1 | 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4 |
| 2 | 27PF 27pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C6 |
| 16 | TBD | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R9, R10, R11, R12, R13, R14 +8 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 180R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 220R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 2 | 130MR 130mR | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6, R7 |
| 1 | 300R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
Injector sensor hub design files
The KiCad project lives in the waterloo-rocketry/canhw repository on GitHub; these links point at the commit this page was built from.
Injector sensor hub: common questions
What microcontroller does the Injector sensor hub use?
The Injector sensor hub is built around the PIC18F26K83, from the PIC family.
How big is the Injector sensor hub PCB?
The Injector sensor hub measures 58.4 × 45.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Injector sensor hub?
58 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Injector sensor hub design files?
From the waterloo-rocketry/canhw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Injector sensor hub design in my own project?
Yes, under the terms of its GPL-3.0 license, which waterloo-rocketry chose for the repository.
Can I test firmware for the Injector sensor hub without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in canhw
STM32
CanardBoard
waterloo-rocketry
100 × 70 mm244 parts6LGPL-3.015STM32
SRAD Altimeter
waterloo-rocketry
71.4 × 71.4 mm133 parts4LGPL-3.015PIC
PropulsionBoard
waterloo-rocketry
56.9 × 61.3 mm99 parts2LGPL-3.015PIC
Rocket power board
waterloo-rocketry
33 × 58.4 mm79 parts4LGPL-3.015PIC
Remote arming
waterloo-rocketry
68.9 × 41.5 mm61 parts4LGPL-3.015STM32
Camera
waterloo-rocketry
45.2 × 32.5 mm58 parts4LGPL-3.015STM32
Processor Board 2025
waterloo-rocketry
48.9 × 52.1 mm57 parts4LGPL-3.015PIC
Camera interface CAN board
waterloo-rocketry
38.6 × 29 mm44 parts4LGPL-3.015STM32
CAN relay
waterloo-rocketry
50 × 43.5 mm43 parts4LGPL-3.015PIC
GPS Board
waterloo-rocketry
54.3 × 28.9 mm41 parts2LGPL-3.015PIC
DAQ CAN support
waterloo-rocketry
86.4 × 35.1 mm31 parts2LGPL-3.015
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379