PropulsionBoard
waterloo-rocketry·canhw·PropulsionBoard/PropulsionBoard.kicad_pcb
About the PropulsionBoard PCB
PropulsionBoard is an open source PIC PCB design by waterloo-rocketry, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 56.9 × 61.3 mm, with 99 components from 57 distinct parts.
Its main chip is the M10578-A2, from the PIC family. Other key parts include the PIC18F26K83, MCP2562, SPX3819M5-L-3-3, INA180 and MS5607-02BA03. By type, the board carries 28 resistors, 18 jumpers, 13 test points, 11 capacitors, 9 connectors and 7 ICs.
It belongs with the rf & radio designs in this gallery.
From the project
Hardware monorepo avionics PCB
This repository tracks the hardware development for the RocketCAN project. All schematics, board designs, and fabrication files are tracked in this repository. The corresponding software running on each board can be found in the cansw repositories. The CAN driver library used is tracked in the canlib repository.
All hardware files were developed in KiCAD.
The RocketCAN project is an extension of the 2018 Flight Instrumentation project. The functions of the original Flight Instrumentation electronics are decoupled into several single-function modules connected by a Controller Area Network…
Main components on the PropulsionBoard
PropulsionBoard bill of materials (BOM)
99 components, 57 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | M10578-A2 MC2562 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | PIC18F26K83 | SOIC-28W_7.5x17.9mm_P1.27mm | U2 |
| 1 | MCP2562 PCA9536DR | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | SPX3819M5-L-3-3 INA180 | SOT-23-5_HandSoldering | U4 |
| 1 | INA180 | SOT-23-5_HandSoldering | U5 |
| 1 | SPX3819M5-L-3-3 | SOT-23-5 | U6 |
| 1 | MS5607-02BA03 | SON125P300X500X100-8N | U7 |
| 3 | SI3420A-TP | SOT-23_Handsoldering | Q1, Q2, Q3 |
| 1 | ABM8G-12.000MHZ-18-D2Y-T Crystal | Resonator-2Pin_W10.0mm_H5.0mm | Y1 |
| 1 | Programming Header | PinHeader_5x2.54_SMD_90deg_952-3198-1-ND | J1 |
| 1 | G125-MH104M4-04AD000P CAN_Connector | connector_Harwin_G125–MG10605M4P | J2 |
| 1 | Valve Connection | connector_Harwin_G125–MG10605M4P | J3 |
| 4 | Conn_01x03_Female | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J4, J5, J6, J9 |
| 2 | Conn_01x02_Female-Connector | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J7, J8 |
| 1 | 0ZCM0008FF2G Fuse 0603 ERB-RE2R00V | Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 2 | Polyfuse 350 mA | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F2, F3 |
| 6 | +12V | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP4, JP7, JP10, JP13, JP16 |
| 6 | +5V | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP2, JP5, JP8, JP11, JP14, JP17 |
| 6 | +3.3V | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP3, JP6, JP9, JP12, JP15, JP18 |
| 1 | TP_5V | KEYSTONE_5000 | TP1 |
Show 37 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CURRAMP5V | KEYSTONE_5000 | TP2 |
| 1 | 36-5001 CURRAMP12V | KEYSTONE_5000 | TP3 |
| 1 | 36-5001 TP_12V | KEYSTONE_5000 | TP4 |
| 1 | TP_3.3V | KEYSTONE_5000 | TP5 |
| 1 | TP_S1A-OUT | KEYSTONE_5000 | TP6 |
| 1 | TP_S2A-OUT | KEYSTONE_5000 | TP7 |
| 1 | TP_S3A-OUT | KEYSTONE_5000 | TP8 |
| 1 | TP_S4A-OUT | KEYSTONE_5000 | TP9 |
| 1 | TP_S5-OUT | KEYSTONE_5000 | TP10 |
| 1 | TP_S6-OUT | KEYSTONE_5000 | TP11 |
| 1 | TP_SCL | KEYSTONE_5000 | TP12 |
| 1 | TP_SDA | KEYSTONE_5000 | TP13 |
| 1 | LED_GREEN | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | LED_BLUE | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | LED_RED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3 |
| 1 | KDZVTR3.6B BAS16GWJ | D_SOD-123 | D4 |
| 2 | BAS16GWJ | D_SOD-123 | D5, D6 |
| 1 | 22PF 10 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 2 | 0.1UF 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C6 |
| 1 | 10UF 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 2 | 1UF 27 pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5 |
| 1 | 22PF 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7 |
| 1 | 2.2UF 1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 22PF 10 nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 1 | 22PF 2.2 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 26PF 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11 |
| 1 | 100R 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 2 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 1 | 10K 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 2 | 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6 |
| 1 | 160 15 mR | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R7 |
| 1 | 160 62 mR | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R8 |
| 1 | 200MR 30K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 4 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R12, R14, R16 |
| 3 | 270R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R13, R15 |
| 8 | TBD | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17, R19, R21, R23, R24, R25, R26, R27 |
| 4 | 90mR | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R20, R22, R28 |
PropulsionBoard design files
The KiCad project lives in the waterloo-rocketry/canhw repository on GitHub; these links point at the commit this page was built from.
PropulsionBoard: common questions
What microcontroller does the PropulsionBoard use?
The PropulsionBoard is built around the M10578-A2, from the PIC family.
How big is the PropulsionBoard PCB?
The PropulsionBoard measures 56.9 × 61.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PropulsionBoard?
99 components, from 57 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PropulsionBoard design files?
From the waterloo-rocketry/canhw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PropulsionBoard design in my own project?
Yes, under the terms of its GPL-3.0 license, which waterloo-rocketry chose for the repository.
Can I test firmware for the PropulsionBoard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in canhw
STM32
CanardBoard
waterloo-rocketry
100 × 70 mm244 parts6LGPL-3.015STM32
SRAD Altimeter
waterloo-rocketry
71.4 × 71.4 mm133 parts4LGPL-3.015PIC
Rocket power board
waterloo-rocketry
33 × 58.4 mm79 parts4LGPL-3.015PIC
Remote arming
waterloo-rocketry
68.9 × 41.5 mm61 parts4LGPL-3.015PIC
Injector sensor hub
waterloo-rocketry
58.4 × 45.7 mm58 parts2LGPL-3.015STM32
Camera
waterloo-rocketry
45.2 × 32.5 mm58 parts4LGPL-3.015STM32
Processor Board 2025
waterloo-rocketry
48.9 × 52.1 mm57 parts4LGPL-3.015PIC
Camera interface CAN board
waterloo-rocketry
38.6 × 29 mm44 parts4LGPL-3.015STM32
CAN relay
waterloo-rocketry
50 × 43.5 mm43 parts4LGPL-3.015PIC
GPS Board
waterloo-rocketry
54.3 × 28.9 mm41 parts2LGPL-3.015PIC
DAQ CAN support
waterloo-rocketry
86.4 × 35.1 mm31 parts2LGPL-3.015
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379