GPS Board

waterloo-rocketry·canhw·gps/gps_2.kicad_pcb

GPS Board layout, top view — open source PIC board by waterloo-rocketry

About the GPS Board

GPS Board is an open source PIC PCB design by waterloo-rocketry, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 54.3 × 28.9 mm, with 41 components from 28 distinct parts.

Its main chip is the PIC18F26K83, from the PIC family. Other key parts include the M10578-A2, MCP2562, SPX3819M5-L-3-3 and INA180. By type, the board carries 14 capacitors, 7 resistors, 5 ICs, 4 test points, 4 diodes and 3 connectors.

It belongs with the rf & radio designs in this gallery.

From the project

Hardware monorepo avionics PCB

This repository tracks the hardware development for the RocketCAN project. All schematics, board designs, and fabrication files are tracked in this repository. The corresponding software running on each board can be found in the cansw repositories. The CAN driver library used is tracked in the canlib repository.

All hardware files were developed in KiCAD.

The RocketCAN project is an extension of the 2018 Flight Instrumentation project. The functions of the original Flight Instrumentation electronics are decoupled into several single-function modules connected by a Controller Area Network…

Main components on the GPS Board

GPS Board bill of materials (BOM)

41 components, 28 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
M10578-A2
U1
1
PIC18F26K83
U2
1
MCP2562
U3
1
SPX3819M5-L-3-3
U4
1
INA180
U5
1
ABM8G-12.000MHZ-18-D2Y-T
Y1
1
Programming Header
J1
1
G125-MH104M4-04AD000P
J2
1
EMPCB.SMAFSTJ.B.HT
J3
1
0ZCM0008FF2G
F1
1
RX
TP1
1
TX
TP2
2
36-5001
36-5001-ND
TP3, TP4
1
WHITE
D1
1
RED
D2
1
BLUE
D3
1
KDZVTR3.6B
D4
2
47NH
47nH
L1, L2
5
22PF
22pF
C1, C7, C9, C10, C13
3
0.1UF
0.1uF
C2, C6, C14
Show 8 more
QtyPartRefs
1
10UF
10uF
C3
2
1UF
1uF
C4, C5
1
2.2UF
2.2uF
C8
2
26PF
26pF
C11, C12
1
100R
R1
3
10K
10k
R2, R3, R4
2
160
R7, R8
1
200MR
200mR
R9

GPS Board design files

The KiCad project lives in the waterloo-rocketry/canhw repository on GitHub; these links point at the commit this page was built from.

GPS Board: common questions

What microcontroller does the GPS Board use?

The GPS Board is built around the PIC18F26K83, from the PIC family.

How big is the GPS Board?

The GPS Board measures 54.3 × 28.9 mm, has 2 copper layers and is 0.7154 mm thick.

How many components are on the GPS Board?

41 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the GPS Board design files?

From the waterloo-rocketry/canhw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the GPS Board design in my own project?

Yes, under the terms of its GPL-3.0 license, which waterloo-rocketry chose for the repository.

Can I test firmware for the GPS Board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in canhw

Similar boards