41 open source boards using the MCP2562
Real designs built with the MCP2562, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
R1 panel
cuspaceflight
50 × 50 mm176 parts2LNo license93MCU Powertrain
mark-belbin
108 × 54 mm152 parts4LGPL-3.043NXP
Kbox hardware
sarfata
100 × 54 mm102 parts2LNo license19STM32
M4psu
cuspaceflight
269 × 155 mm246 parts2LNo license8PIC
Marine GPS
mbouyer
160 × 100 mm107 parts2LBSD-2-Clause6C6021light
deltaphi
100 × 50 mm74 parts2LGPL-3.05PIC
Thermocouple board
waterloo-rocketry
73.9 × 56.6 mm59 parts2LNo license5PIC
Command
mbouyer
69.9 × 84.8 mm34 parts2LBSD-2-Clause2STM32
Scot resolver
philcrump
108.6 × 79.4 mm137 parts2LMIT1STM32
Input board
waterloo-rocketry
111.8 × 61 mm167 parts6LNo license0PIC
Controls-2025-electrical
waterloo-rocketry
50.2 × 40 mm82 parts4LNo license0AVR/Arduino
Bus bridge encoders sonar
makerbus
100 × 50 mm47 parts2LNo license0AVR/Arduino
Bus beaglebone
makerbus
100 × 50 mm44 parts2LNo license0AVR/Arduino
Bus raspberry pi
makerbus
100 × 50 mm42 parts2LNo license0AVR/Arduino
Bus sonar10
makerbus
100 × 50 mm36 parts2LNo license0PIC
All in One Railroad Interface
GBert
85 × 56.5 mm151 parts2LNo license99STM32
SRAD Altimeter
waterloo-rocketry
71.4 × 71.4 mm133 parts4LGPL-3.015STM32
M4pyro
cuspaceflight
100 × 74.9 mm165 parts2LNo license8PIC
Control main
mbouyer
71.1 × 72.4 mm27 parts2LBSD-2-Clause2STM32
M3PSU - MCU Board
cuspaceflight
40 × 40 mm151 parts2LNo license93PIC
PropulsionBoard
waterloo-rocketry
56.9 × 61.3 mm99 parts2LGPL-3.015PIC
Capteur
mbouyer
69.9 × 60 mm26 parts2LBSD-2-Clause2- schematic only · 112 partsSTM32
Automedon
waterloo-rocketry
112 parts2LNo license0 STM32
M3PSU - DC/DC 5V Board
cuspaceflight
39.5 × 39.5 mm140 parts2LNo license93PIC
Rocket power board
waterloo-rocketry
33 × 58.4 mm79 parts4LGPL-3.015PIC
Remote control
mbouyer
74 × 34 mm24 parts2LBSD-2-Clause2Beagle-AI-64-CAN-Part2
SuzieLinux
86.4 × 54.8 mm33 parts2LGPL-3.00PIC
Remote arming
waterloo-rocketry
68.9 × 41.5 mm61 parts4LGPL-3.015AVR/Arduino
DriveControllerLogic
UofSSpaceTeam
85.6 × 51.9 mm66 parts2LNo license5STM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1STM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1STM32
M3radio
cuspaceflight
39.5 × 39.5 mm66 parts2LNo license93PIC
Injector sensor hub
waterloo-rocketry
58.4 × 45.7 mm58 parts2LGPL-3.015STM32
Base
cuspaceflight
40 × 33 mm45 parts2LNo license93STM32
Processor Board 2025
waterloo-rocketry
48.9 × 52.1 mm57 parts4LGPL-3.015PiMainboard
UofSSpaceTeam
116 × 72.3 mm32 parts2LNo license5
How designs wire the MCP2562
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the MCP2562 connects to, and the resistors, capacitors and other passives placed on it.
- The VIO pin has a decoupling capacitor on 16 of 21 designs, most often 100 nF (then 22 µF).
- The VDD pin has a decoupling capacitor on 13 of 21 designs, most often 100 nF (then 10 µF).
- The STBY pin is tied to GND on 15 of 21 designs (a signal on 6).
- The CANH pin has a series resistor on 10 of 21 designs, most often 120 Ω (then 470 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 95% | — |
| VDDpin 3 | Connected to: 5V 95% |
|
| VIOpin 5 | Connected to: 3.3V 100% |
|
| CANHpin 7 | Connected to: A connector 81% |
|
| STBYpin 8 | Connected to: GND 71% · a signal 29% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include All in One Railroad Interface by GBert, M3PSU - MCU Board by cuspaceflight, MCU Powertrain by mark-belbin and Kbox hardware by sarfata.
The MCP2562 in open source designs
The gallery holds 41 open source boards using the MCP2562 from 21 GitHub repositories; a typical one measures about 72.6 × 54 mm and carries around 59 components.
83% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is All in One Railroad Interface by GBert.
Parts used alongside the MCP2562
Microcontrollers on boards using the MCP2562
What boards using the MCP2562 are built for
MCP2562: common questions
Where can I find a MCP2562 reference design?
Each of the 41 boards on this page is a real design using the MCP2562. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP2562 VIO pin?
The VIO pin has a decoupling capacitor on 16 of 21 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 21 open source designs using the MCP2562.
What decoupling capacitors do designs use on the MCP2562 VDD pin?
The VDD pin has a decoupling capacitor on 13 of 21 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 21 open source designs using the MCP2562.
How is the MCP2562 STBY pin connected?
The STBY pin is tied to GND on 15 of 21 designs (a signal on 6). Counted from the KiCad layouts of 21 open source designs using the MCP2562.
What parts are used alongside the MCP2562?
The 74HCT08, MCP2515, 12v input, 5v input and ATMEGA324_DIP40 appear in the most repositories here.
Which microcontrollers do boards using the MCP2562 use?
Most are built on STM32 (15), PIC (14), AVR/Arduino (5) and NXP (1).
How big is a typical board using the MCP2562?
The median is 72.6 × 54 mm, and 83% are two-layer designs.
What is the most popular open source board using the MCP2562?
By GitHub stars, All in One Railroad Interface by GBert, with 99 stars.
Can I simulate one of these boards using the MCP2562 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.