HardLabs

Rt hw v1

ahsanu123·crumbs·realtime-communication/hardware/rt_hw_v1/rt_hw_v1.kicad_pcb

Rt hw v1 PCB layout, top view — open source ESP32 board by ahsanu123

About the Rt hw v1 PCB

Rt hw v1 is an open source ESP32 PCB design by ahsanu123, published on GitHub under the MIT license. It is a 2-layer board measuring 113.4 × 65.1 mm, with 81 components from 45 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the 74HCT245PW, CH340G, BQ27441-G1, BQ24075RGT_DPPM and TPS63001. By type, the board carries 31 resistors, 25 capacitors, 8 ICs, 6 diodes, 4 connectors and 3 switches.

It belongs with the power & battery designs in this gallery.

From the project

🍪 Crumbs - Collection of my DIY Electronic Module

SDMMC is hardware host, and SDIO is the protocol.

- look at esp32 SDMMC documentation here - working POC in STM32F407VGT6 is use this file system exfat-slim, poc already prof library able to reading and writing into file. - make sure to format sdcard to exfat file system, use this command below, make sure you install required dependencies - install with pacman sudo pacman -S exfatprogs parted dosfstools - use lsblk to list all possible sdcard - replace X to possible sdcard listed from lsblk - sudo umount /dev/sdX - sudo wipefs -a /dev/sdX - sudo parted /dev/sdX --script mklabel msdos - sudo…

Main components on the Rt hw v1

74HCT245PWCH340GESP32-S3-WROOM-1BQ27441-G1BQ24075RGT_DPPMTPS63001ADS1115IDGSTPS63002_SEPIC_5V

Rt hw v1 bill of materials (BOM)

81 components, 45 distinct parts.

QtyPartRefs
1
74HCT245PW
74HCT245_TSSOP
MDD(辰达半导体)
U1
1
CH340G
U2
1
ESP32-S3-WROOM-1
U3
1
BQ27441-G1
U4
1
BQ24075RGT_DPPM
U5
1
TPS63001
U6
1
ADS1115IDGS
U7
1
TPS63002_SEPIC_5V
U8
2
SS8050
Q1, Q2
1
USB2UART
J1
1
BattConn
J2
1
ConnBattery
J3
1
SD_Card_Receptacle
J4
1
RST
SW1
1
Boot
SW3
1
RKJXV1224005
PS Joystick
ALPSALPINE(阿尔卑斯阿尔派)
SW9
3
WS2812B-2020
D1, D2, D3
1
green
D4
1
INDICATOR
D5
1
red
D6
Show 25 more
QtyPartRefs
2
22uH
L1, L2
5
100nF
C1, C2, C3, C21, C24
4
1uF
C4, C7, C8, C20
2
4.7uF
C5, C6
3
100nF
C9, C18, C26
6
10uF
C10, C12, C13, C14, C16, C17
2
0.1uF
C11, C15
1
22uF
C19
1
1uF
C22
1
470nF
C23
1
1K
R1
5
10k
R2, R4, R11, R12, R32
1
10K
R3
2
5K1
R5, R8
1
46.4K
R6
1
2K2
R7
3
1k
R9, R30, R31
2
4K7
R10, R18
1
1.13k
R13
2
1K5
R14, R15
2
100
R16, R17
1
10m 1%
R19
3
5K1
R20, R21, R23
1
1M8
R22
5
47K
R24, R25, R26, R27, R28

Rt hw v1 design files

The KiCad project lives in the ahsanu123/crumbs repository on GitHub; these links point at the commit this page was built from.

Rt hw v1: common questions

What microcontroller does the Rt hw v1 use?

The Rt hw v1 is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Rt hw v1 PCB?

The Rt hw v1 measures 113.4 × 65.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rt hw v1?

81 components, from 45 distinct parts. The full bill of materials is listed on this page.

Where can I download the Rt hw v1 design files?

From the ahsanu123/crumbs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Rt hw v1 design in my own project?

Yes, under the terms of its MIT license, which ahsanu123 chose for the repository.

Can I test firmware for the Rt hw v1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in crumbs

Similar boards