13 open source boards using the BQ27441-G1
Real designs built with the BQ27441-G1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ZC95 MKII
CrashOverride85
191.5 × 76 mm319 parts2LGPL-3.0115ESP32
Turpial hardware
btcven
140 × 47 mm177 parts4LCERN-OHL-W-2.03Sharket
zephray
67.2 × 58.2 mm223 parts4LNo license1RP2040/RP2350
PortaPLUTO
kpezeshki
77 × 129 mm135 parts4LNo license1ESP32
Himinds boosting innovation embedded env sensor hw
HiMinds
79 × 79 mm86 parts2LApache-2.01STM32
RJX-Embedded-Training-Kit
MUDAL
69.7 × 70.9 mm103 parts2LGPL-3.00ESP8266
Smartpowerbank2026
MAIK97MAX
83 × 26 mm71 parts4LNo license0ESP32
Ambient air
mawoka-myblock
50 × 35 mm51 parts2LNo license0ESP32
Rt hw v1
ahsanu123
113.4 × 65.1 mm81 parts2LMIT0ESP32
Stencil
mawoka-myblock
50 × 35 mm47 parts2LNo license0ESP32
Main
mawoka-myblock
50 × 35 mm36 parts2LNo license0Psu
bfrigon
44.5 × 30.5 mm40 parts2LCC-BY-SA-4.018AVR/Arduino
Revopod1
tongtongwang86
60 × 37 mm53 parts4LCC-BY-NC-4.05
How designs wire the BQ27441-G1
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the BQ27441-G1 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 8 of 11 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The SCL pin has a pull-up to 3.3V on 8 of 11 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The VDD pin has a capacitor to GND on 8 of 11 designs, most often 470 nF (then 1 µF).
- The GPOUT pin has a pull-up to 3.3V on 8 of 11 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SDApin 1 | Connected to: The microcontroller 73%, a connector 36% |
|
| SCLpin 2 | Connected to: The microcontroller 73%, a connector 36% |
|
| VSSpin 3 | Connected to: GND 82% · a signal 18% | — |
| NCpin 4, 9, 11 | Connected to: Not connected 100% | — |
| VDDpin 5 | Connected to: Signal 82% · VDD 18% |
|
| BATpin 6 | Connected to: A connector 45% · BAT+ 45% |
|
| BINpin 10 | Connected to: Signal 100% |
|
| GPOUTpin 12 | Connected to: The microcontroller 45% |
|
| PADpin 13 | Connected to: GND 78% · a signal 22% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ZC95 MKII by CrashOverride85, Psu by bfrigon, Revopod1 by tongtongwang86 and Turpial hardware by btcven.
The BQ27441-G1 in open source designs
The gallery holds 13 open source boards using the BQ27441-G1 from 11 GitHub repositories; a typical one measures about 69.7 × 47 mm and carries around 81 components.
62% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is ZC95 MKII by CrashOverride85.
Parts used alongside the BQ27441-G1
Microcontrollers on boards using the BQ27441-G1
What boards using the BQ27441-G1 are built for
BQ27441-G1: common questions
Where can I find a BQ27441-G1 reference design?
Each of the 13 boards on this page is a real design using the BQ27441-G1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the BQ27441-G1 SDA pin?
The SDA pin has a pull-up to 3.3V on 8 of 11 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 11 open source designs using the BQ27441-G1.
What pull-up resistor is used on the BQ27441-G1 SCL pin?
The SCL pin has a pull-up to 3.3V on 8 of 11 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 11 open source designs using the BQ27441-G1.
How is the BQ27441-G1 VDD pin connected?
The VDD pin has a capacitor to GND on 8 of 11 designs, most often 470 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the BQ27441-G1.
What parts are used alongside the BQ27441-G1?
The ATMEGA328-A, BQ24072RGT, BQ24075RGT, MT3608 and USBLC6-2P6 appear in the most repositories here.
Which microcontrollers do boards using the BQ27441-G1 use?
Most are built on ESP32 (6), AVR/Arduino (1), ESP8266 (1) and RP2040/RP2350 (1).
How big is a typical board using the BQ27441-G1?
The median is 69.7 × 47 mm, and 62% are two-layer designs.
What is the most popular open source board using the BQ27441-G1?
By GitHub stars, ZC95 MKII by CrashOverride85, with 115 stars.
Can I simulate one of these boards using the BQ27441-G1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.