96 open source boards using the SPX3819M5-L-3-3
Real designs built with the SPX3819M5-L-3-3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Openlager
d-ronin
15.2 × 19.1 mm29 parts4LNo license111ESP8266
Window-Door sensor-Version-5
gadjet
31.5 × 20.6 mm30 parts2LGPL-2.070ESP32
LiteWingV2.5C
jobitjoseph
100 × 100 mm76 parts2LCC-BY-NC-4.054Toern
Soundpauli
160 × 71 mm118 parts4LCC-BY-NC-4.021RP2040/RP2350
ESPesh
Charlio99
25.4 × 25.4 mm36 parts2LCC-BY-NC-4.021Nordic nRF
Jalapeno
GeeWizWow
230.1 × 77.6 mm184 parts2LCC-BY-NC-4.013AVR/Arduino
Arduino
aspro648
68.6 × 53.3 mm43 parts2LNo license12AVR/Arduino
Openstint transponder
zsellera
18.5 × 15 mm34 parts4LNo license12RISC-V
Avaja
Haimrich
70 × 15.5 mm55 parts2LMIT11RP2040/RP2350
Hackxpansion
KOEGlike
52 × 43 mm74 parts4LGPL-3.06A1200FaStRamExpansion
f1ac0
69.9 × 100 mm23 parts2LNo license6RP2040/RP2350
Hackxpansion
hackclub
52 × 43 mm73 parts4LGPL-3.05STM32
FlightController H743
nikipoatgit
47 × 60 mm56 parts2LGPL-3.05HEXBERRY-V-20Q100-0.91
logitiles
65 × 40 mm186 parts4LCERN-OHL-S-2.04STM32
HeadphoneGuitarPracticeAmp
jbush001
80 × 30 mm51 parts4LApache-2.04AVR/Arduino
FC660C-Alt-Controller
YCF
98.3 × 35 mm23 parts2LNo license4RP2040/RP2350
Skinny Chameleon
TweetyDaBird
225.5 × 93 mm180 parts2LNo license3ESP32
BikeNav
utydfd
38 × 101 mm34 parts2LGPL-3.03ESP32
CyberBadge
hspsh
112.5 × 41.5 mm567 parts2LNo license2STM32
STM32C5-eval board
tenko
53.5 × 20 mm39 parts4LMIT2USB-to-UART-CH340g
adaptableCoder
57.3 × 12 mm21 parts2LMIT2AVR/Arduino
Control panel
lucanastasio
65 × 58 mm158 parts2LNo license1RP2040/RP2350
2040Inverter
Kirg5
86.4 × 61.9 mm93 parts4LNo license1Microchip SAM
Romi unified board advanced
WPIRoboticsEngineering
125.1 × 125.7 mm91 parts4LNo license1ESP32
Panel
RamRamAndroid
131 × 100 mm83 parts2LNo license1STM32
Wand
ayuusweetfish
63.2 × 23.9 mm65 parts2LCERN-OHL-S-2.01AVR/Arduino
MCU.ATMEGA328P-AU-Base
kgsully
60 × 63 mm51 parts2LNo license1ESP32
Open-ESP-board
Lasertie
34 × 39.5 mm29 parts2LNo license1ZigbeeRetrofit
tfindlay-au
20 × 50 mm24 parts2LNo license1RISC-V
GateCrasher-CH32V
rmingon
20 × 40 mm12 parts2LMIT1ESP32
FlexNode
AleksaHeler
80 × 106 mm178 parts4LGPL-3.00FPGA
ZYNQ-SoM
Nov4ou
50 × 40 mm136 parts6LCERN-OHL-P-2.00STM32
GalernaDsp
mirrorganger
121 × 121 mm125 parts4LNo license0Microchip SAM
SapphineMinimalR6
ChrisHayward-dev
55.9 × 61 mm121 parts4LNo license0ESP32
Hard-EnvSens
IgorFJensen
60 × 60 mm102 parts2LNo license0STM32
Stm32-flight controller
bassammorsy
108 × 74 mm100 parts4LMIT0
How designs wire the SPX3819M5-L-3-3
Read from the KiCad layouts of 80 open source designs, one per repository: what each pin of the SPX3819M5-L-3-3 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin is tied to 3.3V on 71 of 80 designs (a signal on 8).
- The IN pin is tied to 5V on 63 of 80 designs (GND on 2, a signal on 15).
- The BP pin has a capacitor to GND on 48 of 80 designs, most often 10 nF (then 100 nF).
- The EN pin is tied to 5V on 50 of 80 designs (a signal on 30).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: 5V 79% · a signal 19% | — |
| GNDpin 2 | Connected to: GND 95% | — |
| ENpin 3 | Connected to: 5V 63% · a signal 38% | — |
| BPpin 4 | Connected to: Signal 63% · not connected 35% |
|
| OUTpin 5 | Connected to: 3.3V 89% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Openlager by d-ronin, Window-Door sensor-Version-5 by gadjet, LieWingV2.6.C by jobitjoseph and Corevus toolboard by calithameridi.
The SPX3819M5-L-3-3 in open source designs
The gallery holds 96 open source boards using the SPX3819M5-L-3-3 from 80 GitHub repositories; a typical one measures about 55 × 43 mm and carries around 56 components.
67% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Openlager by d-ronin.
Parts used alongside the SPX3819M5-L-3-3
Microcontrollers on boards using the SPX3819M5-L-3-3
What boards using the SPX3819M5-L-3-3 are built for
SPX3819M5-L-3-3: common questions
Where can I find a SPX3819M5-L-3-3 reference design?
Each of the 96 boards on this page is a real design using the SPX3819M5-L-3-3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the SPX3819M5-L-3-3 OUT pin connected?
The OUT pin is tied to 3.3V on 71 of 80 designs (a signal on 8). Counted from the KiCad layouts of 80 open source designs using the SPX3819M5-L-3-3.
How is the SPX3819M5-L-3-3 IN pin connected?
The IN pin is tied to 5V on 63 of 80 designs (GND on 2, a signal on 15). Counted from the KiCad layouts of 80 open source designs using the SPX3819M5-L-3-3.
How is the SPX3819M5-L-3-3 BP pin connected?
The BP pin has a capacitor to GND on 48 of 80 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 80 open source designs using the SPX3819M5-L-3-3.
What parts are used alongside the SPX3819M5-L-3-3?
The USBLC6-2SC6, CH340E, ESP32-S3-WROOM-1, MSPM0G3507SPTR and TP4056 appear in the most repositories here.
Which microcontrollers do boards using the SPX3819M5-L-3-3 use?
Most are built on ESP32 (26), STM32 (19), RP2040/RP2350 (7) and AVR/Arduino (5).
How big is a typical board using the SPX3819M5-L-3-3?
The median is 55 × 43 mm, and 67% are two-layer designs.
What is the most popular open source board using the SPX3819M5-L-3-3?
By GitHub stars, Openlager by d-ronin, with 111 stars.
Can I simulate one of these boards using the SPX3819M5-L-3-3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.