Telem3

5aji·telem3

Telem3 PCB layout, top view — open source ESP32 board by 5aji

About the Telem3 PCB

Telem3 is an open source ESP32 PCB design by 5aji, published on GitHub. It is a 4-layer board measuring 124 × 80 mm, with 151 components from 71 distinct parts.

Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the STM32L562ZETx, W25Q128JVS, TPS2116, TPS54202DDC and BQ24075RGT. By type, the board carries 50 capacitors, 46 resistors, 13 ICs, 12 diodes, 11 connectors and 8 transistors.

From the project

telem3 kicad project

Main components on the Telem3

Telem3 bill of materials (BOM)

151 components, 71 distinct parts.

QtyPartRefs
1
STM32L562ZETx
U1
2
W25Q128JVS
U2, U3
1
ESP32-C3-MINI-1
U4
1
TPS2116
U5
1
TPS54202DDC
U6
1
BQ24075RGT
U7
1
AP7361C-33E
U8
1
NUP4202
U9
1
TCAN334G
U10
1
L80-R
U11
1
LSM6DS3TR-C
LSM6DS3
U12
1
BME280
U13
7
2N7002
Q1, Q2, Q3, Q4, Q5, Q6, Q8
1
IRLML9301
Q7
1
8MHz
Y1
1
32.768kHz
Y2
1
STM32_TRACE
J1
1
EXPANSION_1
J3
1
ESP32_JTAG
J4
1
BAT
J5
Show 51 more
QtyPartRefs
1
STM_USBC
J6
1
Micro_SD_Card
J7
1
QT1
J8
1
QT2
J9
1
Conn_01x04_Socket
J10
1
CAN_TERMINATION
J11
1
GPS_ANT
J12
1
2.5A
F1
1
DLW43SH510XK2L
FL1
1
BAT_TS_BYP
JP2
1
TS-1187A-B-A-B
RESET
SW1
1
OPT
SW2
1
ESP32_RST
SW3
1
GPS_RST
SW4
1
STA0
D1
1
STA1
D2
1
GOOD_LED
D3
1
STA2
D4
1
FAULT_LED
D5
1
STA3
D6
1
ESP_LED0
D7
1
ESP_LED1
D8
1
SMAJ30CA
D9
1
BZV55B10
D10
1
5V
D11
1
NUP2105L
D12
1
600 @ 600MHz
FB1
1
15u
L1
2
20p
C1, C2
25
0.1u
C3, C9, C10, C11, C12, C13, C14, C15 +17
2
10p
C4, C5
3
1u
C6, C7, C27
8
4.7u
C8, C21, C22, C25, C32, C33, C35, C47
4
10u
C23, C24, C39, C41
1
75p
C29
4
22u
C30, C31, C38, C40
1
4.7n
C44
19
100k
R1, R8, R11, R12, R13, R14, R15, R16 +11
8
330
R2, R3, R4, R5, R6, R7, R9, R10
1
330
R19
1
511k
R21
1
105k
R22
1
46.4k
R23
1
1.18k
R24
1
1.13k
R25
1
49.9
R26
1
13.3k
R28
5
10k
R29, R31, R34, R36, R38
2
5.1k
R30, R32
2
60R
R41, R42
2
0R
R43, R44

Telem3 design files

The KiCad project lives in the 5aji/telem3 repository on GitHub; these links point at the commit this page was built from.

Telem3: common questions

What microcontroller does the Telem3 use?

The Telem3 is built around the ESP32-C3-MINI-1, from the ESP32 family.

How big is the Telem3 PCB?

The Telem3 measures 124 × 80 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the Telem3?

151 components, from 71 distinct parts. The full bill of materials is listed on this page.

Where can I download the Telem3 design files?

From the 5aji/telem3 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Telem3 design in my own project?

The repository has no license, so all rights stay with 5aji. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Telem3 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards