HardLabs

Smart penetrometer.kicad pro

ARTS-Laboratory·Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems·SYS_DEV/Columbia/V0/V0.6/V0.6.3/sensors/hardware/PCB/smart penetrometer/smart penetrometer.kicad_pro/smart penetrometer.kicad_pro.kicad_pcb

Smart penetrometer.kicad pro PCB layout, top view — open source AVR/Arduino board by ARTS-Laboratory
Simulate this board

About the Smart penetrometer.kicad pro PCB

Smart penetrometer.kicad pro is an open source AVR/Arduino PCB design by ARTS-Laboratory, published on GitHub under the CC-BY-SA-4.0 license. It is a 4-layer board measuring 29 × 93.3 mm, with 32 components from 23 distinct parts.

Its main chip is the Arduino Nano, from the AVR/Arduino family. Other key parts include the LM321, ADP124ARHZ-3.3-R7, SN74LVC8T245DGVR, DS3231M and BME260. By type, the board carries 10 resistors, 6 ICs, 6 connectors, 6 capacitors, 2 modules and 1 battery holder.

From the project

Design and development of a deployable UAV smart penetrometer

Main components on the Smart penetrometer.kicad pro

LM321ADP124ARHZ-3.3-R7SN74LVC8T245DGVRDS3231MBME260ADS1115IDGSArduino NanoSD_Card_Module

Smart penetrometer.kicad pro bill of materials (BOM)

32 components, 23 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
LM321
U1
1
ADP124ARHZ-3.3-R7
U2
1
SN74LVC8T245DGVR
U3
1
DS3231M
U4
1
BME260
U5
1
ADS1115IDGS
U7
1
Arduino Nano
A1
1
SD_Card_Module
A2
1
RTD
J1
2
Conn_01x02
J2, J3
1
GEO
J4
1
Conn_02x04
J5
1
EC
J6
1
Battery_Cell
BT1
1
SMZ1_770mV
D1
4
C_0.1uF
C1, C3, C5, C7
2
C_1uF
C2, C6
1
R_32K
R1
1
R_7.5K
R2
1
R_100
R3
Show 3 more
QtyPartRefs
2
R_100K
R4, R7
3
R_10K
R5, R6, R11
2
R_1kOhm
R9, R10

Smart penetrometer.kicad pro design files

The KiCad project lives in the ARTS-Laboratory/Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems repository on GitHub; these links point at the commit this page was built from.

Smart penetrometer.kicad pro: common questions

What microcontroller does the Smart penetrometer.kicad pro use?

The Smart penetrometer.kicad pro is built around the Arduino Nano, from the AVR/Arduino family.

How big is the Smart penetrometer.kicad pro PCB?

The Smart penetrometer.kicad pro measures 29 × 93.3 mm, has 4 copper layers and is 1.999999 mm thick.

How many components are on the Smart penetrometer.kicad pro?

32 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Smart penetrometer.kicad pro design files?

From the ARTS-Laboratory/Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Smart penetrometer.kicad pro design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which ARTS-Laboratory chose for the repository.

Can I test firmware for the Smart penetrometer.kicad pro without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems

Similar boards