HardLabs

Smart penetrometer v0.4.0

ARTS-Laboratory·Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems·SYS_DEV/Columbia/V0/V0.4/V0.4.0/hardware_design/PCB/smart_penetrometer_v0.4.0.kicad_pcb

Smart penetrometer v0.4.0 PCB layout, top view — open source AVR/Arduino board by ARTS-Laboratory
Simulate this board

About the Smart penetrometer v0.4.0 PCB

Smart penetrometer v0.4.0 is an open source AVR/Arduino PCB design by ARTS-Laboratory, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 33 × 74.9 mm, with 44 components from 31 distinct parts.

Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the LM22676MR-5, DS3231M, Battery_Input, 4023 and ADS1115IDGS. By type, the board carries 12 capacitors, 11 ICs, 10 resistors, 4 diodes, 3 connectors and 2 modules.

It belongs with the power & battery designs in this gallery.

From the project

Design and development of a deployable UAV smart penetrometer

Main components on the Smart penetrometer v0.4.0

LM22676MR-5DS3231MBattery_Input4023ADS1115IDGS3v3_Voltage_RegulatorSolar_InputADS1120-PWSRAM(23K256)FS8205ADW01SD_Card_ModuleArduino_Nano_v3.x

Smart penetrometer v0.4.0 bill of materials (BOM)

44 components, 31 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
LM22676MR-5
U1
1
DS3231M
U2
1
Battery_Input
U3
1
4023
U4
1
ADS1115IDGS
U5
1
3v3_Voltage_Regulator
U6
1
Solar_Input
U7
1
ADS1120-PW
U8
1
SRAM(23K256)
U9
1
FS8205A
U10
1
DW01
U11
1
SD_Card_Module
A1
1
Arduino_Nano_v3.x
A2
1
XLR3_Switched
J1
1
Conn_01x11_Female
J2
1
Conn_01x02_Female
J3
1
Battery_Cell
BT1
1
D_Zener_Small
D1
1
B320
D2
1
B350
D3
Show 11 more
QtyPartRefs
1
PMEG6045ETP
D4
1
L
L1
4
C_0.1uF
C1, C9, C10, C11
3
C_10uF
C2, C3, C8
1
C_Small
C4
2
C_0.047uF
C5, C7
1
C_0.47uF
C6
1
CP1_Small
C12
2
R_1MOhm
R1, R2
2
R_800Ohm
R3, R4
6
R_Small_US
R5, R6, R7, R8, R9, R10

Smart penetrometer v0.4.0 design files

The KiCad project lives in the ARTS-Laboratory/Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems repository on GitHub; these links point at the commit this page was built from.

Smart penetrometer v0.4.0: common questions

What microcontroller does the Smart penetrometer v0.4.0 use?

The Smart penetrometer v0.4.0 is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.

How big is the Smart penetrometer v0.4.0 PCB?

The Smart penetrometer v0.4.0 measures 33 × 74.9 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Smart penetrometer v0.4.0?

44 components, from 31 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Smart penetrometer v0.4.0 design files?

From the ARTS-Laboratory/Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Smart penetrometer v0.4.0 design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which ARTS-Laboratory chose for the repository.

Can I test firmware for the Smart penetrometer v0.4.0 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Smart-Penetrometer-with-Edge-Computing-and-Intelligent-Embedded-Systems

Similar boards