24 open source boards using the INA180A1
Real designs built with the INA180A1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
ESC Board
FPV-Drone-STM32F411
48.8 × 53.1 mm70 parts4LNo license57STM32
Weather station
Invactive
90 × 32 mm59 parts2LNo license7AVR/Arduino
Main PS Board
zachrjt
85 × 94.5 mm73 parts2LNo license2ESP32
Dreimaskin-ELS
jonasnic
95.6 × 86.1 mm71 parts4LNo license1STM32
ESC Board
IoT-App-Development-Company
48.8 × 53.1 mm70 parts4LNo license1STM32
RC Charger
aokblast
200 × 100 mm296 parts4LNo license0STM32
Board
Filip-Kin
84 × 141 mm235 parts2LNo license0ESP32
Atlas carrier ctrl
md-sazzad-eee
130 × 100 mm145 parts4LNo license0ESP32
Prod pdu
vd-rd
141 × 40 mm95 parts2LNo license0RP2040/RP2350
Hene controllerv3
l1g4v
100 × 91 mm84 parts4LGPL-3.00ESP32
Telescope
Rio6
56.3 × 77 mm75 parts2LNo license0STM32
PUEiE
Michal-Md
48.3 × 31.6 mm56 parts2LNo license0STM32
Custom esc 35a
divyanshuprakas-h
30 × 16 mm56 parts4LNo license0Ryan
garth-martinsen
45.3 × 37.7 mm21 parts2LGPL-3.00Lps regulator rev 12
jerryok826
136.2 × 62.6 mm122 parts2LMIT1STM32
Radio kiosk
Filip-Kin
84 × 133 mm188 parts2LNo license0Circuito Final - Circuito externo
DeniseViltes
124.7 × 134.4 mm76 parts2LNo license0STM32
Radio kiosk fixed
Filip-Kin
84 × 133 mm188 parts2LNo license0STM32
Psu
kajusK
81 × 60 mm103 parts2LNo license0RP2040/RP2350
BDCMotorControlBoard
nunosousa
110 × 37 mm87 parts4LMIT0- schematic only · 85 partsSTM32
Flashlight full v1-1
ahmadtak-3212
85 parts6LNo license0 AVR/Arduino
DataDisplay
nunosousa
38.1 × 69.3 mm30 parts2LMIT0STM32
Panelized pompe sap
ENACRobotique
93 × 146 mm18 parts2LNo license2LightSource
nunosousa
40 × 50 mm22 parts2LMIT0
How designs wire the INA180A1
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the INA180A1 connects to, and the resistors, capacitors and other passives placed on it.
- The - pin has a series resistor on 10 of 19 designs, most often 20 mΩ (then 200 Ω).
- The V+ pin has a decoupling capacitor on 10 of 19 designs, most often 100 nF (then 1 µF).
- The GND pins have a series resistor on 9 of 19 designs, most often 1 kΩ (then 10 kΩ).
- The + pin has a series resistor on 9 of 19 designs, most often 20 mΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 2 | Connected to: GND 50% · a signal 47% |
|
| +pin 3 | Connected to: A connector 26% |
|
| -pin 4 | Connected to: Signal 68% · GND 16% |
|
| V+pin 5 | Connected to: 3.3V 89% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESC Board by FPV-Drone-STM32F411, Weather station by Invactive, Panelized pompe sap by ENACRobotique and Main PS Board by zachrjt.
The INA180A1 in open source designs
The gallery holds 24 open source boards using the INA180A1 from 20 GitHub repositories; a typical one measures about 84 × 69.3 mm and carries around 76 components.
63% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is ESC Board by FPV-Drone-STM32F411.
Parts used alongside the INA180A1
Microcontrollers on boards using the INA180A1
What boards using the INA180A1 are built for
INA180A1: common questions
Where can I find a INA180A1 reference design?
Each of the 24 boards on this page is a real design using the INA180A1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA180A1 - pin?
The - pin has a series resistor on 10 of 19 designs, most often 20 mΩ (then 200 Ω). Counted from the KiCad layouts of 19 open source designs using the INA180A1.
What decoupling capacitors do designs use on the INA180A1 V+ pin?
The V+ pin has a decoupling capacitor on 10 of 19 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 19 open source designs using the INA180A1.
What resistor goes on the INA180A1 GND pin?
The GND pins have a series resistor on 9 of 19 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 19 open source designs using the INA180A1.
What parts are used alongside the INA180A1?
The AP2112K-3.3, SP3485EN-L/TR, STM32F411CEU6, TLV76601QWDRBRQ1 and TPS62153RGTT appear in the most repositories here.
Which microcontrollers do boards using the INA180A1 use?
Most are built on STM32 (12), ESP32 (4), AVR/Arduino (2) and RP2040/RP2350 (2).
How big is a typical board using the INA180A1?
The median is 84 × 69.3 mm, and 63% are two-layer designs.
What is the most popular open source board using the INA180A1?
By GitHub stars, ESC Board by FPV-Drone-STM32F411, with 57 stars.
Can I simulate one of these boards using the INA180A1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.