Spool

TheCacophonyProject·spool-pcb·spool/spool.kicad_pcb

Spool PCB layout, top view — open source RP2040/RP2350 board by TheCacophonyProject

About the Spool PCB

Spool is an open source RP2040/RP2350 PCB design by TheCacophonyProject, published on GitHub under the CERN-OHL-W-2.0 license. It is a 4-layer board measuring 80 × 99 mm, with 133 components from 57 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the TPS63070RNMR, AS5600-ASOT, DRV8871DDA, W25Q128JVS and LMR14050S. By type, the board carries 46 capacitors, 41 resistors, 12 ICs, 11 diodes, 6 connectors and 4 switches.

From the project

- 2 x Crimped leads: 455-4118-ND Can chop in half and use 2 of the ends for the motor and 2 for the magnet - 1 x 8 Pin cable assembly 455-3842-ND for connecting main and plug board. - 3 x Protection Diodes SS54-HF to be hand soldered onto the plug board.

- 2 x Crimped leads: 455-4118-ND Can chop in half and use 2 of the ends for the motor and 2 for the magnet - 1 x 8 Pin cable assembly 455-3842-ND for connecting main and plug board. - 3 x Protection Diodes SS54-HF to be hand soldered onto the plug board.

- 2 x Photo interrupter DY-ITR8402 - 1 x 2 Pin JST XA housing XAP-02V-1 - 1 x 3 Pin JST XA housing XAP-03V-1 - 2 x 8 Pin JST XA Plug S08B-XASK-1(LF)(SN) - 1 x Magnet rotary position sensor? Not too sure if this will end up being used or not. AS5600-ASOT

Main components on the Spool

Spool bill of materials (BOM)

133 components, 57 distinct parts.

QtyPartRefs
1
TPS63070RNMR
U1
1
AS5600-ASOT
U3
1
DRV8871DDA
U6
1
W25Q128JVS
U7
1
RP2040
U8
1
LMR14050S
U9
1
HT75xx-1-SOT89
U10
1
PCF8563T
U14
1
INA219AxDCN
U102
2
DY-ITR8402
U103, U104
1
M24C02-WMN
U106
1
Motor_DC
M1
2
Servo
M2, M3
1
AO3400A
Q1
1
2N7002
Q2
1
Q_NMOS_GSD
Q101
1
Crystal_GND24
Y1
1
Crystal
Y2
1
USB_B_Micro
J1
1
Conn_01x03
J3
Show 37 more
QtyPartRefs
1
Switch_1
J4
2
Switch_2
J6, J9
1
Conn_01x08
J8
1
Buzzer
BZ1
1
USB_BOOT
SW1
1
RESET
SW2
1
SW_Coded_SH-7010
SW4
1
SW_Push_DPDT
SW5
10
D
D2, D4, D5, D6, D7, D8, D9, D10 +2
1
D_Shockley
D17
1
FerriteBead
FB1
1
1.5H
L1
1
4.7uH
L2
1
ElectromagneticActor
L101
4
22uF 25V
C1, C2, C28, C29
2
2.2uF
C3, C27
2
10uF
C4, C10
10
22uF
C5, C6, C7, C8, C36, C46, C47, C48 +2
16
100nF
C9, C11, C12, C13, C14, C15, C16, C17 +8
5
1uF
C20, C21, C25, C26, C30
2
12pF
C23, C24
2
22pF
C31, C32
2
100uF
C34, C35
1
22nF
C37
1
470k
R1
6
10k
R2, R6, R7, R20, R21, R23
1
150k
R3
8
100k
R4, R10, R12, R14, R25, R101, R102, R115
2
33ohm
R16, R17
15
1k
R19, R32, R34, R35, R37, R38, R39, R40 +7
1
47k
R22
1
560
R26
1
680
R27
1
100R
R31
1
33k
R33
1
100mΩ
R103
2
150Ω
R104, R105

Spool design files

The KiCad project lives in the TheCacophonyProject/spool-pcb repository on GitHub; these links point at the commit this page was built from.

Spool: common questions

What microcontroller does the Spool use?

The Spool is built around the RP2040, from the RP2040/RP2350 family.

How big is the Spool PCB?

The Spool measures 80 × 99 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Spool?

133 components, from 57 distinct parts. The full bill of materials is listed on this page.

Where can I download the Spool design files?

From the TheCacophonyProject/spool-pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Spool design in my own project?

Yes, under the terms of its CERN-OHL-W-2.0 license, which TheCacophonyProject chose for the repository.

Can I test firmware for the Spool without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in spool-pcb

Similar boards