21 open source boards using the DW01
Real designs built with the DW01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Joule Chief
fishPointer
84 × 98 mm90 parts2LMIT25ESP32
Main board
card-io-ecg
85 × 55 mm51 parts4LNo license22ESP32
Tuxmini v03
tux-friend
32 × 32 mm78 parts2LGPL-3.018Raspberry Pi
PiUPS
diminDDL
87.4 × 56 mm110 parts2LCERN-OHL-W-2.015Microchip SAM
Kicon-2020-virtual badge
gregdavill
100 × 100 mm600 parts4LCC-BY-SA-4.013AVR/Arduino
Smart penetrometer v0.4.0
ARTS-Laboratory
33 × 74.9 mm44 parts2LCC-BY-SA-4.06ESP8266
Another esp8266 sensor board
brev-dev
54.9 × 95 mm75 parts2LGPL-3.05Meshphone
DerRKDCB
60 × 80 mm72 parts2LNo license5STM32
Ws28xx led driver
Knifa
80 × 25 mm66 parts2LNo license3ESP32
ESP32 LORA Chat
jharvey
121.9 × 101.6 mm222 parts4LGPL-3.01ESP32
Dancing forest
sequoia-hope
322.5 × 183.5 mm216 parts4LCustom license1ESP32
Iguana
iowlabs
80 × 50 mm112 parts2LNo license1Pi hat LoRa
Doenec
65 × 56 mm72 parts2LMIT1ESP32
Feniks
marijn1606
91 × 22 mm52 parts2LNo license1Rgb ring
emmanuelprakash177-gi
84 × 84 mm126 parts2LNo license0STM32
Kinematic outfits
ZephyrCloudNine
74.9 × 57.2 mm82 parts4LNo license0Echometer
wzwqoo
36.6 × 100 mm74 parts4LNo license0ESP32
Trackball
mornepousse
52 × 72.1 mm51 parts2LNo license0Joule Thief
fishPointer
129.8 × 50.8 mm32 parts2LMIT25ESP32
Dancing forest version 1
sequoia-hope
147.9 × 147.9 mm162 parts4LCustom license1Pi hat ups
Doenec
65 × 56 mm62 parts4LMIT1
How designs wire the DW01
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the DW01 connects to, and the resistors, capacitors and other passives placed on it.
- The CS pin has a resistor to GND on 18 of 18 designs, most often 1 kΩ.
- The VCC pin has a series capacitor on 16 of 18 designs, most often 100 nF (then 1 µF).
- The TD pin is left unconnected on 18 of 18 designs.
- The GND pin has a series capacitor on 14 of 18 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 2 | Connected to: Signal 100% |
|
| TDpin 4 | Connected to: Not connected 100% | — |
| VCCpin 5 | Connected to: Signal 94% |
|
| GNDpin 6 | Connected to: FS8205A 56%, a connector 50% · GND 17% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Joule Thief by fishPointer, Main board by card-io-ecg, Tuxmini v03 by tux-friend and PiUPS by diminDDL.
The DW01 in open source designs
The gallery holds 21 open source boards using the DW01 from 18 GitHub repositories; a typical one measures about 80 × 72.1 mm and carries around 75 components.
62% are two-layer designs, the rest use four layers or more, and 48% carry an open source license.
The most starred is Joule Chief by fishPointer.
Parts used alongside the DW01
Microcontrollers on boards using the DW01
What boards using the DW01 are built for
DW01: common questions
Where can I find a DW01 reference design?
Each of the 21 boards on this page is a real design using the DW01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the DW01 CS pin?
The CS pin has a resistor to GND on 18 of 18 designs, most often 1 kΩ. Counted from the KiCad layouts of 18 open source designs using the DW01.
How is the DW01 VCC pin connected?
The VCC pin has a series capacitor on 16 of 18 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 18 open source designs using the DW01.
How is the DW01 TD pin connected?
The TD pin is left unconnected on 18 of 18 designs. Counted from the KiCad layouts of 18 open source designs using the DW01.
What parts are used alongside the DW01?
The FS8205A, TP4056, MT3608, DS3231M and RFM95W-915S2 appear in the most repositories here.
Which microcontrollers do boards using the DW01 use?
Most are built on ESP32 (8), STM32 (2), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the DW01?
The median is 80 × 72.1 mm, and 62% are two-layer designs.
What is the most popular open source board using the DW01?
By GitHub stars, Joule Chief by fishPointer, with 25 stars.
Can I simulate one of these boards using the DW01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.