19 open source boards using the ISO1540
Real designs built with the ISO1540, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PiPLC-Mainboard
Chrismettal
158 × 85 mm144 parts2LCC-BY-SA-4.019STM32
ASPECT2
xboxoneresearch
60 × 60 mm116 parts4LNo license17RP2040/RP2350
CellKeeper
cellkeeper-bms
260 × 113 mm405 parts4LGPL-3.011RP2040/RP2350
CellKeeper-BMS
clowrey
306 × 113 mm423 parts4LGPL-3.09PIC
Elerix cpm
ELERIX
171 × 101 mm417 parts2LNo license4STM32
Ph
Ranthalion
59.4 × 32.3 mm32 parts2LMIT3NXP
VehicleController
UNCAMotorsports
99.1 × 57.2 mm139 parts2LMIT2DMM KiCAD V4 next
oihdesigns
68.5 × 53.3 mm79 parts4LNo license2Tiepielcr hardware
martijnschouten
150 × 50 mm240 parts4LGPL-3.00EDL Project 2026
segf4u1t-139
182 × 126.2 mm237 parts2LNo license0STM32
Digital signal converter
jadranm
160 × 108 mm177 parts4LNo license0Raspberry Pi
Audio
leesanghun-droid
120 × 120 mm149 parts4LNo license0NXP
VehicleControllerwut
UNCAMotorsports
99.1 × 57.2 mm139 parts2LMIT2- schematic only · 72 parts
BMS EXTERNAL V1RA
Stefanhg
72 parts4LNo license0 I2c
multigcs
13.5 × 24.5 mm8 parts2LGPL-2.091THTIC
MetalMusings
41.5 × 30.5 mm23 parts2LNo license93AVR/Arduino
DMM Feather Redux
oihdesigns
85.5 × 47.4 mm60 parts4LNo license2THTIC2
MetalMusings
41.5 × 30.5 mm23 parts2LNo license93FeatherVoltmeterPCBA
oihdesigns
23.5 × 51.1 mm28 parts4LNo license2
How designs wire the ISO1540
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the ISO1540 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC1 pin has a decoupling capacitor on 9 of 14 designs, most often 100 nF (then 1 µF).
- The SDA1 pin has a pull-up to 5V on 9 of 14 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The SCL1 pin has a pull-up to 3.3V on 8 of 14 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The GND2 pin has a series capacitor on 6 of 14 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCC1pin 1 | Connected to: 5V 79% · a signal 21% |
|
| SDA1pin 2 | Connected to: A connector 64%, the microcontroller 21% |
|
| SCL1pin 3 | Connected to: A connector 64%, the microcontroller 21% |
|
| GND1pin 4 | Connected to: GND 100% | — |
| GND2pin 5 | Connected to: A connector 21% · GND 43% |
|
| SCL2pin 6 | Connected to: A connector 29%, the microcontroller 21% |
|
| SDA2pin 7 | Connected to: A connector 29%, the microcontroller 21% |
|
| VCC2pin 8 | Connected to: 3.3V 50% · a signal 50% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include THTIC by MetalMusings, I2c by multigcs, PiPLC-Mainboard by Chrismettal and ASPECT2 by xboxoneresearch.
The ISO1540 in open source designs
The gallery holds 19 open source boards using the ISO1540 from 15 GitHub repositories; a typical one measures about 99.1 × 57.2 mm and carries around 139 components.
53% use four copper layers or more, and 42% carry an open source license.
The most starred is THTIC2 by MetalMusings.
Parts used alongside the ISO1540
Microcontrollers on boards using the ISO1540
What boards using the ISO1540 are built for
ISO1540: common questions
Where can I find a ISO1540 reference design?
Each of the 19 boards on this page is a real design using the ISO1540. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ISO1540 VCC1 pin?
The VCC1 pin has a decoupling capacitor on 9 of 14 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 14 open source designs using the ISO1540.
What pull-up resistor is used on the ISO1540 SDA1 pin?
The SDA1 pin has a pull-up to 5V on 9 of 14 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 14 open source designs using the ISO1540.
What pull-up resistor is used on the ISO1540 SCL1 pin?
The SCL1 pin has a pull-up to 3.3V on 8 of 14 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 14 open source designs using the ISO1540.
What parts are used alongside the ISO1540?
The ADS1115, AM26LV32EIDR, AMS1117-3.3, F0505S-1WR3 and INA228 appear in the most repositories here.
Which microcontrollers do boards using the ISO1540 use?
Most are built on STM32 (3), NXP (2), RP2040/RP2350 (2) and AVR/Arduino (1).
How big is a typical board using the ISO1540?
The median is 99.1 × 57.2 mm, and 47% are two-layer designs.
What is the most popular open source board using the ISO1540?
By GitHub stars, THTIC2 by MetalMusings, with 93 stars.
Can I simulate one of these boards using the ISO1540 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.