40 open source boards using the ADS1115

Real designs built with the ADS1115, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

40 boardsClear filters|Most starred

How designs wire the ADS1115

Read from the KiCad layouts of 30 open source designs, one per repository: what each pin of the ADS1115 connects to, and the resistors, capacitors and other passives placed on it.

  • The VDD pin has a decoupling capacitor on 18 of 29 designs, most often 100 nF (then 1 µF).
  • The SDA pin has a pull-up to 3.3V on 15 of 29 designs, most often 10 kΩ (then 4.7 kΩ).
  • The SCL pin has a pull-up to 3.3V on 14 of 29 designs, most often 4.7 kΩ (then 2.2 kΩ).
ALERTpin 2Connected to: Signal 53% · not connected 30% · GND 17%
  • Pull-up to VCC on 37% · 10 kΩ (8), 100 kΩ (1)
GNDpin 3Connected to: GND 80% · a signal 20%
VDDpin 8Connected to: 3.3V 76% · a signal 21%
  • Decoupling capacitor on 62% · 100 nF (17), 1 µF (1), 10 µF (1)
SDApin 9Connected to: ADS1115 21%, a connector 21%
  • Pull-up to 3.3V on 52% · 10 kΩ (4), 4.7 kΩ (3), 2.2 kΩ (3)
SCLpin 10Connected to: ADS1115 21%, a connector 21%
  • Pull-up to 3.3V on 48% · 4.7 kΩ (3), 2.2 kΩ (3), 10 kΩ (3)

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OPEN ECU by aeonSolutions, Zynface V5 by zynthian, BiasPro by ToneAlchemy and CellKeeper by cellkeeper-bms.

The ADS1115 in open source designs

The gallery holds 40 open source boards using the ADS1115 from 32 GitHub repositories; a typical one measures about 77 × 93 mm and carries around 69 components.

68% are two-layer designs, the rest use four layers or more, and 65% carry an open source license.

The most starred is OPEN ECU by aeonSolutions.

Microcontrollers on boards using the ADS1115

ADS1115: common questions

Where can I find a ADS1115 reference design?

Each of the 40 boards on this page is a real design using the ADS1115. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ADS1115 VDD pin?

The VDD pin has a decoupling capacitor on 18 of 29 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 30 open source designs using the ADS1115.

What pull-up resistor is used on the ADS1115 SDA pin?

The SDA pin has a pull-up to 3.3V on 15 of 29 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 30 open source designs using the ADS1115.

What pull-up resistor is used on the ADS1115 SCL pin?

The SCL pin has a pull-up to 3.3V on 14 of 29 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 30 open source designs using the ADS1115.

What parts are used alongside the ADS1115?

The AHT20, ATSHA204A-MAHDA-T, LMR33630ADDA, 74LVC125 and ADM7150 appear in the most repositories here.

Which microcontrollers do boards using the ADS1115 use?

Most are built on AVR/Arduino (6), ESP32 (6), RP2040/RP2350 (4) and Raspberry Pi (3).

How big is a typical board using the ADS1115?

The median is 77 × 93 mm, and 68% are two-layer designs.

What is the most popular open source board using the ADS1115?

By GitHub stars, OPEN ECU by aeonSolutions, with 160 stars.

Can I simulate one of these boards using the ADS1115 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part