6 open source boards using the ISO1050DUBR
Real designs built with the ISO1050DUBR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
BMS-Version-4
0hasant
100 × 100 mm238 parts2LNo license2ESP32
LTC6811 ESP32 V3
tetra-aero
320 × 55 mm575 parts2LGPL-3.00Microchip SAM
Chademo hardware
larsrengersen
100 × 107.8 mm129 parts4LMIT0STM32
BMS-Master
UCDFS
135.1 × 159.4 mm218 parts2LNo license0AVR/Arduino
BMS Sensor
weaslepalace
80 × 30 mm44 parts2LNo license0ESP32
ESP32 Master V2
tetra-aero
105 × 90 mm99 parts2LGPL-3.00
How designs wire the ISO1050DUBR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ISO1050DUBR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC1 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF).
- The GND2 pin has a series capacitor on 2 of 5 designs, most often 30 pF (then 100 nF).
- The GND2 pin has a capacitor to the supply on 2 of 5 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCC1pin 1 | Connected to: 3.3V 80% · a signal 20% |
|
| GND1pin 4 | Connected to: GND 100% | — |
| GND2pin 5 | Connected to: A connector 80% · GND 20% |
|
| VCC2pin 8 | Connected to: 5V 60% · a signal 40% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BMS-Version-4 by 0hasant, Chademo hardware by larsrengersen, ESP32 Master V2 by tetra-aero and BMS-Master by UCDFS.
The ISO1050DUBR in open source designs
The gallery holds 6 open source boards using the ISO1050DUBR from 5 GitHub repositories; a typical one measures about 102.5 × 95 mm and carries around 174 components.
83% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is BMS-Version-4 by 0hasant.
Parts used alongside the ISO1050DUBR
Microcontrollers on boards using the ISO1050DUBR
What boards using the ISO1050DUBR are built for
ISO1050DUBR: common questions
Where can I find a ISO1050DUBR reference design?
Each of the 6 boards on this page is a real design using the ISO1050DUBR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ISO1050DUBR VCC1 pin?
The VCC1 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the ISO1050DUBR.
How is the ISO1050DUBR GND2 pin connected?
The GND2 pin has a series capacitor on 2 of 5 designs, most often 30 pF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the ISO1050DUBR.
What parts are used alongside the ISO1050DUBR?
The AMC1301DWV, ISL28022FUZ-T7A, LTC6820IMS#PBF, OPA2197IDR and SN6501DBVR appear in the most repositories here.
Which microcontrollers do boards using the ISO1050DUBR use?
Most are built on ESP32 (2), STM32 (2), AVR/Arduino (1) and Microchip SAM (1).
How big is a typical board using the ISO1050DUBR?
The median is 102.5 × 95 mm, and 83% are two-layer designs.
What is the most popular open source board using the ISO1050DUBR?
By GitHub stars, BMS-Version-4 by 0hasant, with 2 stars.
Can I simulate one of these boards using the ISO1050DUBR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.