6 open source boards using the LM2576
Real designs built with the LM2576, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PIC
Hope bike
Le-Dome-RDS
129 × 66 mm88 parts2LNo license8ADB-3020-CDV
Testato
160.5 × 100.6 mm115 parts2LCC-BY-NC-4.05AVR/Arduino
CW-CONTROLLER
prusa3d
126 × 57 mm247 parts4LNo license3OBeMS
johnbeardmore
180 × 120 mm123 parts2LLGPL-3.03ESP32
Smart regulator
physiii
82.5 × 48.6 mm35 parts2LNo license1REACH Robot
ReGame-VR
68.8 × 98.6 mm27 parts2LNo license0
How designs wire the LM2576
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM2576 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 100 µF).
- Pin 2 has a inductor on 5 of 6 designs, most often 100 µH (then 47 µH).
- Pin 3 is tied to GND on 5 of 6 designs.
- Pin 5 is tied to GND on 4 of 6 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 67% · 36V 33% |
|
| Pin 2 | Connected to: Signal 100% |
|
| Pin 3 | Connected to: GND 83% · a signal 17% | — |
| Pin 4 | Connected to: Signal 83% · 5V 17% |
|
| Pin 5 | Connected to: GND 67% · a signal 33% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hope bike by Le-Dome-RDS, ADB-3020-CDV by Testato, OBeMS by johnbeardmore and CW-CONTROLLER-PCB by prusa3d.
The LM2576 in open source designs
The gallery holds 6 open source boards using the LM2576 from 6 GitHub repositories; a typical one measures about 127.5 × 82.3 mm and carries around 102 components.
83% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Hope bike by Le-Dome-RDS.
Microcontrollers on boards using the LM2576
What boards using the LM2576 are built for
LM2576: common questions
Where can I find a LM2576 reference design?
Each of the 6 boards on this page is a real design using the LM2576. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2576 pin 1 connected?
Pin 1 has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 6 open source designs using the LM2576.
How is the LM2576 pin 2 connected?
Pin 2 has a inductor on 5 of 6 designs, most often 100 µH (then 47 µH). Counted from the KiCad layouts of 6 open source designs using the LM2576.
How is the LM2576 pin 3 connected?
Pin 3 is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the LM2576.
Which microcontrollers do boards using the LM2576 use?
Most are built on AVR/Arduino (1), ESP32 (1) and PIC (1).
How big is a typical board using the LM2576?
The median is 127.5 × 82.3 mm, and 83% are two-layer designs.
What is the most popular open source board using the LM2576?
By GitHub stars, Hope bike by Le-Dome-RDS, with 8 stars.
Can I simulate one of these boards using the LM2576 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.