6 open source boards using the 74HC540
Real designs built with the 74HC540, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
8b alu slice
tmarhguy
235 × 202.4 mm1088 parts4LSHL-2.12WildWillyR5Hardware
dkjonas
94.4 × 92.2 mm52 parts4LNo license1PointController
46nori
220 × 180 mm125 parts2LGPL-3.00NXP
5x7 Controller
rixth
70 × 43 mm29 parts2LNo license0AVR/Arduino
CFT DFP Board
alexiosc
233.4 × 280 mm186 parts2LGPL-3.06AVR/Arduino
Debugging Front Panel
alexiosc
280 × 164.6 mm165 parts2LGPL-3.06
How designs wire the 74HC540
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the 74HC540 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
- The G2 pin is tied to GND on 3 of 5 designs (a signal on 2).
- The G1 pin has a pull-up to 3.3V on 2 of 5 designs, most often 100 kΩ (then 10 kΩ).
- The A0 pin has a pull-up to 5V on 2 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| G1pin 1 | Connected to: 74HC540 40% · GND 40% |
|
| A0pin 2 | Connected to: Signal 100% |
|
| GNDpin 10 | Connected to: GND 100% | — |
| G2pin 19 | Connected to: GND 60% · a signal 40% |
|
| VCCpin 20 | Connected to: 5V 100% |
|
15 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CFT DFP Board by alexiosc, 8b alu slice by tmarhguy, WildWillyR5Hardware by dkjonas and PointController by 46nori.
The 74HC540 in open source designs
The gallery holds 6 open source boards using the 74HC540 from 5 GitHub repositories; a typical one measures about 226.7 × 172.3 mm and carries around 145 components.
67% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is CFT DFP Board by alexiosc.
Microcontrollers on boards using the 74HC540
What boards using the 74HC540 are built for
74HC540: common questions
Where can I find a 74HC540 reference design?
Each of the 6 boards on this page is a real design using the 74HC540. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74HC540 VCC pin?
The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the 74HC540.
How is the 74HC540 G2 pin connected?
The G2 pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the 74HC540.
What pull-up resistor is used on the 74HC540 G1 pin?
The G1 pin has a pull-up to 3.3V on 2 of 5 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the 74HC540.
Which microcontrollers do boards using the 74HC540 use?
Most are built on AVR/Arduino (2) and NXP (1).
How big is a typical board using the 74HC540?
The median is 226.7 × 172.3 mm, and 67% are two-layer designs.
What is the most popular open source board using the 74HC540?
By GitHub stars, CFT DFP Board by alexiosc, with 6 stars.
Can I simulate one of these boards using the 74HC540 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.