6 open source boards using the ACS711xLCTR-25AB
Real designs built with the ACS711xLCTR-25AB, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Battry-Management-System
src94
156.7 × 80.6 mm143 parts2LGPL-3.03Afe 230v 16a
kyuditsky
67.7 × 86.4 mm69 parts2LNo license0NXP
Flight-Computer
Tim-Drake0
82 × 38 mm61 parts2LNo license0Carte puissance crac
Darkzveller
67.1 × 123.5 mm51 parts2LNo license0Load
AresEnsea
50 × 50 mm52 parts4LNo license7HUB
SJSURoboticsTeam
159.2 × 93 mm45 parts4LNo license1
How designs wire the ACS711xLCTR-25AB
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ACS711xLCTR-25AB connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF.
- The FAULT pin is left unconnected on 4 of 6 designs (a signal on 2).
- The IP+ pins have a series resistor on 3 of 6 designs, most often 2 Ω (then 1 kΩ).
- The VIOUT pin has a capacitor to GND on 3 of 6 designs, most often 18 pF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IP+pin 1, 2 | Connected to: A connector 33% · V+ 33% |
|
| GNDpin 5 | Connected to: GND 83% · a signal 17% | — |
| FAULTpin 6 | Connected to: Not connected 67% · a signal 33% | — |
| VIOUTpin 7 | Connected to: The microcontroller 33%, a connector 33% |
|
| VCCpin 8 | Connected to: 3.3V 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Load by AresEnsea, Battry-Management-System by src94, HUB by SJSURoboticsTeam and Carte puissance crac by Darkzveller.
The ACS711xLCTR-25AB in open source designs
The gallery holds 6 open source boards using the ACS711xLCTR-25AB from 6 GitHub repositories; a typical one measures about 74.8 × 83.5 mm and carries around 57 components.
67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Load by AresEnsea.
Microcontrollers on boards using the ACS711xLCTR-25AB
What boards using the ACS711xLCTR-25AB are built for
ACS711xLCTR-25AB: common questions
Where can I find a ACS711xLCTR-25AB reference design?
Each of the 6 boards on this page is a real design using the ACS711xLCTR-25AB. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ACS711xLCTR-25AB VCC pin?
The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the ACS711xLCTR-25AB.
How is the ACS711xLCTR-25AB FAULT pin connected?
The FAULT pin is left unconnected on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the ACS711xLCTR-25AB.
What resistor goes on the ACS711xLCTR-25AB IP+ pin?
The IP+ pins have a series resistor on 3 of 6 designs, most often 2 Ω (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the ACS711xLCTR-25AB.
Which microcontrollers do boards using the ACS711xLCTR-25AB use?
Most are built on AVR/Arduino (1) and NXP (1).
How big is a typical board using the ACS711xLCTR-25AB?
The median is 74.8 × 83.5 mm, and 67% are two-layer designs.
What is the most popular open source board using the ACS711xLCTR-25AB?
By GitHub stars, Load by AresEnsea, with 7 stars.
Can I simulate one of these boards using the ACS711xLCTR-25AB before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.