7 open source boards using the ENC28J60
Real designs built with the ENC28J60, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
POE
reportingsjr
100 × 50 mm123 parts4LCERN-OHL-1.216AVR/Arduino
PlipUltimate
tehKaiN
50 × 50 mm51 parts2LGPL-2.013Microchip SAM
USMR Engineering Board
DarmorGamz
66 × 68.6 mm55 parts4LCustom license9STM32
Dc electronic load
joeferner
106.8 × 73.5 mm107 parts2LNo license6USSTCM
UofSSpaceTeam
280.6 × 229.7 mm139 partsNo license5STM32
Stm32-network rs232
joeferner
85.2 × 47.2 mm57 parts2LNo license5AVR/Arduino
ATmega1284EthernetController
46nori
100 × 80 mm45 parts4LNo license0
How designs wire the ENC28J60
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ENC28J60 connects to, and the resistors, capacitors and other passives placed on it.
- The VCAP pin has a capacitor to GND on 7 of 7 designs, most often 10 µF.
- The TPIN- pin has a series resistor on 7 of 7 designs, most often 50 Ω (then 49.9 Ω).
- The TPIN+ pin has a series resistor on 7 of 7 designs, most often 50 Ω (then 49.9 Ω).
- The RBIAS pin has a resistor to GND on 7 of 7 designs, most often 2.32 kΩ (then 2.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCAPpin 1 | Connected to: Signal 100% |
|
| VSSpin 2 | Connected to: GND 100% | — |
| CLKOUTpin 3 | Connected to: Not connected 100% | — |
| WOLpin 5 | Connected to: Not connected 100% | — |
| RESETpin 10 | Connected to: The microcontroller 57% |
|
| VSSRXpin 11 | Connected to: GND 100% | — |
| TPIN-pin 12 | Connected to: A connector 86% |
|
| TPIN+pin 13 | Connected to: A connector 86% |
|
| RBIASpin 14 | Connected to: Signal 100% |
|
| VDDTXpin 15 | Connected to: 3.3V 100% |
|
| TPOUT-pin 16 | Connected to: A connector 86% |
|
| TPOUT+pin 17 | Connected to: A connector 86% |
|
| VSSTXpin 18 | Connected to: GND 100% | — |
| VDDRXpin 19 | Connected to: 3.3V 100% |
|
| VDDPLLpin 20 | Connected to: 3.3V 100% |
|
| VSSPLLpin 21 | Connected to: GND 100% | — |
| VSSOSCpin 22 | Connected to: GND 100% | — |
| OSC1pin 23 | Connected to: Signal 100% |
|
| OSC2pin 24 | Connected to: Signal 71% · not connected 29% |
|
| VDDOSCpin 25 | Connected to: 3.3V 100% |
|
| LEDBpin 26 | Connected to: Signal 100% |
|
| LEDApin 27 | Connected to: Signal 100% |
|
| VDDpin 28 | Connected to: 3.3V 100% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include POE by reportingsjr, PlipUltimate by tehKaiN, USMR Engineering Board by DarmorGamz and Dc electronic load by joeferner.
The ENC28J60 in open source designs
The gallery holds 7 open source boards using the ENC28J60 from 7 GitHub repositories; a typical one measures about 100 × 68.6 mm and carries around 57 components.
50% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is POE by reportingsjr.
Microcontrollers on boards using the ENC28J60
What boards using the ENC28J60 are built for
ENC28J60: common questions
Where can I find a ENC28J60 reference design?
Each of the 7 boards on this page is a real design using the ENC28J60. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ENC28J60 VCAP pin connected?
The VCAP pin has a capacitor to GND on 7 of 7 designs, most often 10 µF. Counted from the KiCad layouts of 7 open source designs using the ENC28J60.
What resistor goes on the ENC28J60 TPIN- pin?
The TPIN- pin has a series resistor on 7 of 7 designs, most often 50 Ω (then 49.9 Ω). Counted from the KiCad layouts of 7 open source designs using the ENC28J60.
What resistor goes on the ENC28J60 TPIN+ pin?
The TPIN+ pin has a series resistor on 7 of 7 designs, most often 50 Ω (then 49.9 Ω). Counted from the KiCad layouts of 7 open source designs using the ENC28J60.
Which microcontrollers do boards using the ENC28J60 use?
Most are built on STM32 (3), AVR/Arduino (2) and Microchip SAM (1).
How big is a typical board using the ENC28J60?
The median is 100 × 68.6 mm, and 50% are two-layer designs.
What is the most popular open source board using the ENC28J60?
By GitHub stars, POE by reportingsjr, with 16 stars.
Can I simulate one of these boards using the ENC28J60 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.